SN74LVC1G3157YEPR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-XFBGA, DSBGA |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 15Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 2.3V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74LVC1G3157 |
| Output | COMMON OUTPUT |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 10μA |
| Turn On Delay Time | 24 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 13 ns |
| -3db Bandwidth | 340MHz |
| On-State Resistance (Max) | 15Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 57 dB |
| Channel Capacitance (CS(off), CD(off)) | 5.2pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 5.7ns, 3.8ns |
| Charge Injection | 7pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -54dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 7.5ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Height Seated (Max) | 0.5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
SN74LVC1G3157YEPR Overview
Shipping overseas is convenient due to the electrical component's packing in 6-XFBGA, DSBGA. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. The operating temperature is extended to around -40°C~85°C TA. In total, there are 6 terminations. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 2.3V volts, the electrical component should be turned on and run. The electronic part body is injected with 6 pins. Based on SPDT switching circuits, these analog multiplexers work. There are 1 circuits in this switch device. Try searching with 74LVC1G3157 if you're looking for variants. This digital multiplexer has 15Ohm internal resistance. For details about the functions of 6 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. A cost-effective Single supply type analogue multiplexer. 1.65V should be the lowest voltage fed to the electronic component. An operating current of 1μA would be sufficient for this switch device. The voltage required by this switch device is 1.65V~5.5V, draining from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 10μA. A total of COMMON OUTPUT outputs are available on this analog switch ic.
SN74LVC1G3157YEPR Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 340MHz
SN74LVC1G3157YEPR Applications
There are a lot of Texas Instruments SN74LVC1G3157YEPR Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- Low-Voltage
- Medical Instrumentation
- Mechanical reed relay replacement
- Video signal routing
- RGB switches
- Battery Powered Instruments
- SDH
- Cell phones
- Microwave transmission systems
