SN74LVC1G66DBVR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 11.198062mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Base Part Number | 74LVC1G66 |
| Pin Count | 5 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Analog IC - Other Type | SPDT |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 1μA |
| Output Current | 50mA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Propagation Delay | 600 ps |
| Turn On Delay Time | 4.2 ns |
| Supply Type | Single |
| Bandwidth | 195MHz |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 10Ohm |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 58 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| On-state Resistance Match-Nom | 12Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 4.2ns, 5ns |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Drain to Source Resistance | 12Ohm |
| Normal Position | NC |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LVC1G66DBVR Overview
The electrical component comes in SC-74A, SOT-753 packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Cut Tape (CT). A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Temperatures around -40°C~85°C TA are extended for operation. A total of 5 terminations have been recorded. By its 1 channels, the electronic component provides high-quality output. Powered by a 1.8V voltage supply, the electrical part should be switched on and run. 5 pins are injected to the electronic part body. Circuits based on SPST - NO switching are used to construct these analog switch ics. 74LVC1G66 can be used to search for analog multiplexer variants. Analog switches have 10Ohm internal resistance. To find out what the 5 pins do, please refer to the datasheets. normally, users should not supply switches with voltages higher than 5.5V. A cost-effective Single supply type analogue multiplexer. 1.65V is the lowest voltage the electrical component should receive. In order to operate this switch device, it would need a current of 10μA. Draining from a single voltage supply, this analog switch requires a voltage of 1.65V~5.5V. The switch multiplexer may be damaged if it is exposed to voltage greater than 10μA. Integrated with an analog IC SPDT. There are 195MHz bandwidths for data transfer. This electronic component presents a Drain to Source resistance of 12Ohm.
SN74LVC1G66DBVR Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 300MHz
Bandwidth: 195MHz
Drain-to-Source resistance: 12Ohm
SN74LVC1G66DBVR Applications
There are a lot of Texas Instruments SN74LVC1G66DBVR Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- Video switching
- Mechanical reed relay replacement
- HDTV
- Medical
- Digital Cross-Connects
- Digital cross connects (DSX-1)
- Video signal routing
- PBXs
- Industrial
