SN74LVC1G66DBVRE4
| Parameters | |
|---|---|
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74LVC1G66 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Analog IC - Other Type | SPDT |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Propagation Delay | 600 ps |
| Turn On Delay Time | 4.2 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 58 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| On-state Resistance Match-Nom | 12Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 4.2ns, 5ns |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NC |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 11.198062mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
SN74LVC1G66DBVRE4 Overview
Presented in SC-74A, SOT-753, this electrical component is convenient for overseas shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Increasing operating temperature to around -40°C~85°C TA. There are 5 terminations totally. As a result of its 1 channels, this electronic component provides high-quality output. An 1.8V voltage supply should allow the electrical part to be turned on and run. A key feature of the 5 series is the inclusion of this electronic part as part of its design. The analog switch ics are built using SPST - NO switching circuits. Try searching with 74LVC1G66 if you're looking for variants. Internally, this switch multiplexer has a resistance of 10Ohm. To find out what the 5 pins do, please refer to the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. An effective Single supply digital multiplexer. It is recommended that the electrical component receives a voltage of 1.65V. It would be sufficient to run this analogue multiplexer with 10μA current. A voltage of 1.65V~5.5V is required to drain this analog switch from a single voltage supply. A voltage higher than 10μA may cause damage to the switch multiplexer. There is an integrated analog IC SPDT in the module. There are 300MHz bandwidths for data transfer.
SN74LVC1G66DBVRE4 Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 300MHz
Bandwidth: 300MHz
SN74LVC1G66DBVRE4 Applications
There are a lot of Texas Instruments SN74LVC1G66DBVRE4 Analog Switches & Multiplexers ICs applications.
- Digital cross connects (DSX-1)
- PDH Multiplexers
- Modems
- Industrial
- Video signal routing
- DSLAMs
- Medical systems
- Switching Systems
- SONET
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
