SN74LVC1G66DCKRE4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Weight | 2.494758mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74LVC1G66 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Analog IC - Other Type | SPDT |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Propagation Delay | 600 ps |
| Turn On Delay Time | 4.2 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 58 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| On-state Resistance Match-Nom | 12Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 4.2ns, 5ns |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NC |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LVC1G66DCKRE4 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 5-TSSOP, SC-70-5, SOT-353. High reliability is achieved by using advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Operating temperature around -40°C~85°C TA extended. Total terminations are 5. A high-quality output is provided by the electrical component's 1 channels. A 1.8V voltage supply should turn on and run the electronic component. The electrical component body receives 5 pins. Based on SPST - NO switching circuits, these analog multiplexers work. Try searching with 74LVC1G66 if you're looking for variants. In this multiplexer, the internal resistance is 10Ohm. To find out what the 5 pins do, please refer to the datasheets. A voltage higher than 5.5V should not normally be supplied to the switches. Single supply type digital switch with a low cost. 1.65V is the lowest voltage that should be fed to the electronic electronic part. This multiplexer would work with 10μA current. This analogue multiplexer requires a voltage of 1.65V~5.5V when it drains from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 10μA. Integrated with an analog IC SPDT. A 300MHz-bandwidth can be used for data transfer.
SN74LVC1G66DCKRE4 Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 300MHz
Bandwidth: 300MHz
SN74LVC1G66DCKRE4 Applications
There are a lot of Texas Instruments SN74LVC1G66DCKRE4 Analog Switches & Multiplexers ICs applications.
- Public switching systems
- Battery Powered Instruments
- Avionics test equipment
- Microwave transmission systems
- HDTV
- Fault Tolerant Systems
- Automatic test equipment
- Fiber In The Loop (FITL)
- ATM
- Battery Powered Systems
