SN74LVC1G66DCKRG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Weight | 2.494758mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Base Part Number | 74LVC1G66 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Analog IC - Other Type | SPDT |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Propagation Delay | 600 ps |
| Turn On Delay Time | 4.2 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 58 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| On-state Resistance Match-Nom | 12Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 4.2ns, 5ns |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NC |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LVC1G66DCKRG4 Overview
The electrical component comes in 5-TSSOP, SC-70-5, SOT-353 packaging, which makes it convenient to ship overseas. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~85°C TA extended. Total terminations are 5. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 1.8V volts, the electrical part can be powered up and run. It is part of the design of the 5 series that this electronic component is included. A SPST - NO switching circuit is used for these analog switches. Use 74LVC1G66 to search for variants of the digital switches. A 10Ohm internal resistance characterizes this multiplexer. You can find the functions of the 5 pins in the datasheets. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. The analog switch ic is of the Single supply type and is cost-effective. 1.65V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 10μA would be sufficient for this switch device. This analogue multiplexer requires a voltage of 1.65V~5.5V when it drains from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 10μA. With a SPDT analog IC integrated into the board. In 300MHz-bandwidths, data can be transferred.
SN74LVC1G66DCKRG4 Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 300MHz
Bandwidth: 300MHz
SN74LVC1G66DCKRG4 Applications
There are a lot of Texas Instruments SN74LVC1G66DCKRG4 Analog Switches & Multiplexers ICs applications.
- MP3 players
- Low-Voltage
- Medical Instrumentation
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Video switching
- PDH Multiplexers
- Voice over IP/DSL – Integrated Access Devices, Smart
- DVD-R
- Signal routing between systems
- ISDN NT1/TA
