SN74LVC1G66DCKT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Weight | 2.494758mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Termination | SMD/SMT |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Base Part Number | 74LVC1G66 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Analog IC - Other Type | SPDT |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Propagation Delay | 600 ps |
| Turn On Delay Time | 4.2 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 58 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| On-state Resistance Match-Nom | 12Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 4.2ns, 5ns |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NC |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LVC1G66DCKT Overview
The electronic part can be shipped overseas conveniently because it is packaged in 5-TSSOP, SC-70-5, SOT-353. High reliability is achieved by using advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 5. A 1 channel electronic part produces high-quality output. If the voltage supply is 1.8V volts, the electrical component should be turned on and run. As part of the design of the 5 series, this electronic part has been incorporated into the system. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching with 74LVC1G66 if you're looking for variants. There is 10Ohm internal resistance in this digital multiplexer. To find out what the functions of 5 pins are, please refer to their datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Analogue multiplexers of the Single supply type that are cost-effective. It is recommended to use 1.65V as the lowest voltage for the electrical part. In order to operate this switch device, it would need a current of 10μA. Analogue multiplexers require a 1.65V~5.5V voltage to drain from a single voltage supply. If you put voltage higher than 10μA on the digital multiplexer, damage may occur. A SPDT analog IC is integrated into the board. It is possible to transfer data over a 300MHz-bandwidth.
SN74LVC1G66DCKT Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 300MHz
Bandwidth: 300MHz
SN74LVC1G66DCKT Applications
There are a lot of Texas Instruments SN74LVC1G66DCKT Analog Switches & Multiplexers ICs applications.
- PBXs
- Relay replacements
- Channelized and Unchannelized DS3 applications
- Power routing
- Data switching
- Routers
- Intelligent PBX
- Cable Modem
- High reliability control systems
- Audio signal routing
