SN74LVC1G66DRYR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-UFDFN |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Base Part Number | 74LVC1G66 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Analog IC - Other Type | SPDT |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Propagation Delay | 600 ps |
| Turn On Delay Time | 4.2 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 10Ohm |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 58 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| On-state Resistance Match-Nom | 12Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 4.2ns, 5ns |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NC |
| Height | 600μm |
| Length | 1.45mm |
| Width | 1mm |
| Thickness | 500μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
SN74LVC1G66DRYR Overview
The electronic component is convenient to ship overseas because it is packed in a 6-UFDFN. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operational temperature extended around -40°C~85°C TA. 6 terminations have been made so far. A electrical component with 1 channels is capable of high-quality output. When the electronic component is given a voltage of 1.8V, it should be turned on and run. A SPST - NO switching circuit is used to build these analog multiplexers. Try searching with 74LVC1G66 to find analog multiplexer variants. In this multiplexer, the internal resistance is 10Ohm. For functions related to 6 pins, please refer to the datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Single supply type digital switch with a low cost. It is recommended to use 1.65V as the lowest voltage for the electrical part. For this digital switch to work, 10μA current would suffice. A voltage of 1.65V~5.5V is required to drain this analog switch from a single voltage supply. Putting voltage greater than 10μA on the multiplexer may cause damage. With a SPDT analog IC integrated into the board. In 300MHz-bandwidths, data can be transferred.
SN74LVC1G66DRYR Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 300MHz
Bandwidth: 300MHz
SN74LVC1G66DRYR Applications
There are a lot of Texas Instruments SN74LVC1G66DRYR Analog Switches & Multiplexers ICs applications.
- Switching Systems
- Precision test equipment
- Power routing
- Signal routing between systems
- PBX interfaces
- Cross Connects
- Industrial and process control systems
- Communications systems
- E1 Multiplexer
- Microprocessor Controlled Analog Systems
