SN74LVC1G66QDCKRQ1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.3V |
| Base Part Number | 74LVC1G66 |
| Output | COMMON OUTPUT |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Propagation Delay | 2.6 ns |
| Turn On Delay Time | 4.2 ns |
| Supply Type | Single |
| Bandwidth | 195MHz |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 42 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 7.2ns, 6.9ns |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 8.9ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NO |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LVC1G66QDCKRQ1 Overview
The electronic component is convenient to ship overseas because it is packed in a 5-TSSOP, SC-70-5, SOT-353. The advanced packaging method Tape & Reel (TR) provides high reliability. The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Increasing operating temperature to around -40°C~125°C TA. In total, there have been 5 terminations. Due to its 1 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 2.3V voltage supply. As part of its design, the 5 series is equipped with this electronic component. SPST - NO switching circuits are used in these analog switch ics. Look for analog switch ic variants by searching with 74LVC1G66. This digital multiplexer has 10Ohm internal resistance. For details about the functions of 5 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 5.5V voltage to the switch device. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage fed to the electronic component should be 1.65V. For this multiplexer to operate, 10μA current would be sufficient. Using a single voltage supply, this switch device consumes 1.65V~5.5V volts. If you put voltage higher than 10μA on the digital multiplexer, damage may occur. In this switch multiplexer, there are COMMON OUTPUT outputs available. In 195MHz-bandwidths, data can be transferred. The series starts with Automotive, AEC-Q100.
SN74LVC1G66QDCKRQ1 Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 300MHz
Bandwidth: 195MHz
SN74LVC1G66QDCKRQ1 Applications
There are a lot of Texas Instruments SN74LVC1G66QDCKRQ1 Analog Switches & Multiplexers ICs applications.
- High reliability control systems
- PBX interfaces
- Fiber to the Home
- Cell phones
- E1 Network Equipment
- Automatic test equipment
- Multi-Line E1 Interface Cards
- High-Voltage
- PDAs
- Ultrasound
