SN74LVC1G66YZAR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-XFBGA, DSBGA |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 10Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 2.3V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74LVC1G66 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 4.2 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 42 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 4.2ns, 5ns |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 6.9ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NO |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LVC1G66YZAR Overview
As the electronic part is packed in 5-XFBGA, DSBGA, international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Temperatures around -40°C~85°C TA are extended for operation. The total number of terminations is 5. The electronic part delivers high-quality output through its 1 channels. With a 2.3V voltage supply, the electrical component should be turned on and run. A total of 5 pins are injected into the electrical part body. A SPST - NO switching circuit is used to build these analog multiplexers. Try searching with 74LVC1G66 if you're looking for variants. As far as internal resistance is concerned, it has 10Ohm. For details about the functions of 5 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Analogue multiplexer with a Single supply type that is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 1.65V. This multiplexer would work with 10μA current. Using only a single voltage supply, this analog switch requires 1.65V~5.5V voltage. It may damage the digital multiplexer if the voltage is higher than 10μA.
SN74LVC1G66YZAR Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 300MHz
SN74LVC1G66YZAR Applications
There are a lot of Texas Instruments SN74LVC1G66YZAR Analog Switches & Multiplexers ICs applications.
- Medical systems
- Imaging
- Battery Powered Instruments
- Fiber In The Loop (FITL)
- Industrial
- Relay Replacement
- MP3 players
- Switching Systems
- Avionics and Military Systems
- Multi-Line E1 Interface Cards
