SN74LVC1G66YZPR
| Parameters | |
|---|---|
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74LVC1G66 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Analog IC - Other Type | SPDT |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Propagation Delay | 600 ps |
| Turn On Delay Time | 4.2 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 58 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| On-state Resistance Match-Nom | 12Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 4.2ns, 5ns |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NC |
| Height | 500μm |
| Length | 1.75mm |
| Width | 1.25mm |
| Thickness | 310μm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-XFBGA, DSBGA |
| Number of Pins | 5 |
| Weight | 1.587573mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
SN74LVC1G66YZPR Overview
The electronic component is convenient to ship overseas because it is packed in a 5-XFBGA, DSBGA. To ensure high reliability, a new packaging method Cut Tape (CT) is used. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Operating temperature extended to -40°C~85°C TA. In total, 5 terminations have occurred. The electronic part provides high-quality output because it has 1 channels. An 1.8V voltage supply should allow the electrical part to be turned on and run. This electronic part can be found in the 5 series. Unlike digital switches, these are based on SPST - NO switching circuits. Search with 74LVC1G66 if you are looking for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 10Ohm. To find out what the functions of 5 pins are, please refer to their datasheets. A voltage higher than 5.5V should not normally be supplied to the switches. A cost-effective Single supply type analogue multiplexer. The lowest voltage fed to the electronic component should be 1.65V. It would be sufficient to run this analogue multiplexer with 10μA current. Using only a single voltage supply, this analog switch requires 1.65V~5.5V voltage. Put voltage above 10μA on the multiplexer to cause damage. This product is integrated with an analog integrated circuit (IC) of type SPDT. The transfer of data can be performed over 300MHz bandwidths.
SN74LVC1G66YZPR Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 300MHz
Bandwidth: 300MHz
SN74LVC1G66YZPR Applications
There are a lot of Texas Instruments SN74LVC1G66YZPR Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- Routers
- Medical Instrumentation
- Intelligent PBX
- Residential Gateways, Home Gateway/Router
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Battery Powered Systems
- Cable PC
- Switching Systems
- PDAs
