Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 1 week ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-XFBGA, DSBGA |
Number of Pins |
8 |
Weight |
2.296311mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Cut Tape (CT) |
JESD-609 Code |
e1 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
13Ohm |
Terminal Finish |
Tin/Silver/Copper (Sn/Ag/Cu) |
Subcategory |
Multiplexers or Switches |
Technology |
CMOS |
Terminal Position |
BOTTOM |
Terminal Form |
BALL |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
2.3V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
74LVC2G53 |
Pin Count |
8 |
Number of Outputs |
2 |
Qualification Status |
Not Qualified |
Polarity |
Non-Inverting |
Number of Channels |
2 |
Number of Circuits |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.65V |
Operating Supply Current |
1μA |
Max Supply Current |
1μA |
Propagation Delay |
600 ps |
Turn On Delay Time |
10.3 ns |
Supply Type |
Single |
Bandwidth |
300MHz |
Turn-Off Delay Time |
9.4 ns |
-3db Bandwidth |
300MHz |
On-State Resistance (Max) |
13Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
50 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
10pF |
On-state Resistance Match-Nom |
5Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
4.5ns, 8ns |
Channel-to-Channel Matching (ΔRon) |
2 Ω (Max) |
Crosstalk |
-58dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
7.9ns |
Voltage - Supply, Single (V+) |
1.65V~5.5V |
Height |
500μm |
Length |
1.25mm |
Width |
2.25mm |
Thickness |
310μm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
SN74LVC2G53YZPR Overview
Presented in 8-XFBGA, DSBGA, this electrical component is convenient for overseas shipping. High reliability is provided by advanced packaging method Cut Tape (CT). Multiplexers like this are mounted in the Surface Mount position. Multiplexer and demultiplexer circuits have a number 2:1. Operational temperature extended around -40°C~85°C TA. The total number of terminations is 8. A electrical component with 2 channels is capable of high-quality output. An 2.3V voltage supply should allow the electrical part to be turned on and run. An injection of 8 pins is performed into the body of the electrical component. On the other hand, analog switches can be constructed using SPDT switching circuits. 1 circuits are used in this analogue multiplexer. Try searching for the analog switch ic with 74LVC2G53 if you are looking for variants. As far as internal resistance is concerned, it has 13Ohm. The functions of 8 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexers or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended that the electrical component receives a voltage of 1.65V. The analogue multiplexer could operate on 1μA current. A voltage of 1.65V~5.5V is required to drain this analog switch from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. The transfer of data can be performed over 300MHz bandwidths. There are 2 outputs on the analogue multiplexer.
SN74LVC2G53YZPR Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 300MHz
Bandwidth: 300MHz
SN74LVC2G53YZPR Applications
There are a lot of Texas Instruments SN74LVC2G53YZPR Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- High-Voltage
- PCMCIA cards
- MP3 players
- Battery Powered Instruments
- New designs requiring multiplexer functions
- High reliability control systems
- Communications systems
- Channel Banks
- ATM