Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 1 week ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-VFSOP (0.091, 2.30mm Width) |
Number of Pins |
8 |
Weight |
9.610488mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
Resistance |
10Ohm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Multiplexers or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
2.3V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
74LVC2G66 |
Output |
SEPARATE OUTPUT |
Pin Count |
8 |
Qualification Status |
Not Qualified |
Power Supplies |
3.3V |
Number of Channels |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.65V |
Operating Supply Current |
10μA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Propagation Delay |
600 ps |
Turn On Delay Time |
10 ns |
Supply Type |
Single |
Bandwidth |
300MHz |
Turn-Off Delay Time |
10.5 ns |
-3db Bandwidth |
300MHz |
On-State Resistance (Max) |
10Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
42 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
6pF |
On-state Resistance Match-Nom |
5Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
3.9ns, 6.3ns |
Channel-to-Channel Matching (ΔRon) |
2 Ω (Max) |
Crosstalk |
-58dB @ 1MHz |
Switching |
MAKE-BEFORE-BREAK |
Switch-on Time-Max |
5.6ns |
Switch-off Time-Max |
6.9ns |
Voltage - Supply, Single (V+) |
1.65V~5.5V |
Normal Position |
NO |
Height |
900μm |
Length |
2.3mm |
Width |
2mm |
Thickness |
850μm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
SN74LVC2G66DCUTE4 Overview
This electronic part is conveniently packaged in 8-VFSOP (0.091, 2.30mm Width), making it easy to ship abroad. High reliability is ensured by the advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 1:1. Increasing operating temperature to around -40°C~85°C TA. In total, there have been 8 terminations. A high-quality output is provided by the electrical component's 2 channels. It is safe to turn on and run the electronic component with a 2.3V voltage supply. An electrical component of this type can be found in the 8 series. These analog multiplexers are built based on SPST - NO switching circuits. Try searching for the analog switch ic with 74LVC2G66 if you are looking for variants. Analog switches have 10Ohm internal resistance. Datasheets for 8 pin functions are available upon request. It is a typical Multiplexers or Switches analog multiplexer. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. Digital switch that provides Single power at a cost-effective price. A low voltage of 1.65V should be applied to the electronic component. In order to operate this switch device, it would need a current of 10μA. A voltage of 1.65V~5.5V is required for this switch device, which drains from a single voltage source. A voltage higher than 1μA may cause damage to the switch multiplexer. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. It is possible to transfer data over a 300MHz-bandwidth.
SN74LVC2G66DCUTE4 Features
2 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 300MHz
Bandwidth: 300MHz
SN74LVC2G66DCUTE4 Applications
There are a lot of Texas Instruments SN74LVC2G66DCUTE4 Analog Switches & Multiplexers ICs applications.
- Power routing
- Relay Replacement
- Industrial and process control systems
- Relay replacements
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Intelligent PBX
- Industrial control systems
- PBXs
- 65 V DACs
- Audio and video signal routing