SN74LVC2G66YEPR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-XFBGA, DSBGA |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 10Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 2 |
| Supply Voltage | 2.3V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74LVC2G66 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3.3V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 10μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 10 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 10.5 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 42 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 3.9ns, 6.3ns |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -58dB @ 1MHz |
| Switch-on Time-Max | 5.6ns |
| Switch-off Time-Max | 6.9ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NO |
| Height Seated (Max) | 0.5mm |
| Length | 1.9mm |
| RoHS Status | ROHS3 Compliant |
SN74LVC2G66YEPR Overview
Presented in 8-XFBGA, DSBGA, this electrical component is convenient for overseas shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. This analog switch is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~85°C TA. There are 8 terminations totally. As a result of its 1 channels, this electronic component provides high-quality output. In the case of a voltage supply of 2.3V volts, the electrical part can be powered up and run. A key feature of the 8 series is the inclusion of this electronic part as part of its design. The analog switch ics are built using SPST - NO switching circuits. The circuits in this analogue multiplexer number 2. Try searching for the analog switch ic with 74LVC2G66 if you are looking for variants. It has an internal resistance of 10Ohm. Datasheets for functions of 8 pins are available. A analogue multiplexer of this type is a Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. The digital multiplexer has a low cost Single supply. 1.65V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 10μA would be sufficient for this switch device. A voltage of 1.65V~5.5V is required to drain this analog switch from a single voltage supply. When the digital multiplexer is charged above 10μA, damage can occur. There are SEPARATE OUTPUT outputs on this analog switch ic.
SN74LVC2G66YEPR Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 300MHz
SN74LVC2G66YEPR Applications
There are a lot of Texas Instruments SN74LVC2G66YEPR Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- Automotive applications
- Medical
- Medical systems
- Optical Applications
- Voice over IP/DSL – Integrated Access Devices, Smart
- Precision data acquisition
- Industrial and process control systems
- Relay replacements
- PBXs
