SN74LVC2G66YZAR

3.9ns, 6.3ns SPST - NO 10Ohm BOTTOM Analog Switches 74LVC2G66 8 Pins 100nA 2.3V 8-XFBGA, DSBGA

Manufacturer: Texas Instruments
Nocochips NO: 815-SN74LVC2G66YZAR
Package: 8-XFBGA, DSBGA
Datasheet: -
Stock: 205
Description: 3.9ns, 6.3ns SPST - NO 10Ohm BOTTOM Analog Switches 74LVC2G66 8 Pins 100nA 2.3V 8-XFBGA, DSBGA(Kg)

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	8-XFBGA, DSBGA
Number of Pins	8
Operating Temperature	-40°C~85°C TA
Packaging	Cut Tape (CT)
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
Resistance	10Ohm
Subcategory	Multiplexer or Switches
Technology	CMOS
Terminal Position	BOTTOM
Terminal Form	BALL
Peak Reflow Temperature (Cel)	NOT SPECIFIED
Number of Functions	2
Supply Voltage	2.3V
Terminal Pitch	0.5mm
Time@Peak Reflow Temperature-Max (s)	NOT SPECIFIED
Base Part Number	74LVC2G66
Output	SEPARATE OUTPUT
Pin Count	8
Qualification Status	Not Qualified
Polarity	Non-Inverting
Power Supplies	3.3V
Number of Channels	2
Max Supply Voltage	5.5V
Min Supply Voltage	1.65V
Operating Supply Current	10μA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	10 ns
Supply Type	Single
Turn-Off Delay Time	10.5 ns
-3db Bandwidth	300MHz
On-State Resistance (Max)	10Ohm
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	42 dB
Current - Leakage (IS(off)) (Max)	100nA
Channel Capacitance (CS(off), CD(off))	6pF
On-state Resistance Match-Nom	5Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	3.9ns, 6.3ns
Channel-to-Channel Matching (ΔRon)	2 Ω (Max)
Crosstalk	-58dB @ 1MHz
Switch-on Time-Max	5.6ns
Switch-off Time-Max	6.9ns
Voltage - Supply, Single (V+)	1.65V~5.5V
Normal Position	NO
Height Seated (Max)	0.5mm
Length	1.9mm
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

SN74LVC2G66YZAR Overview

Packed in 8-XFBGA, DSBGA, the electronic component is convenient for shipping overseas. A high level of reliability can be achieved through the use of an advanced packaging method Cut Tape (CT). Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a ratio of 1:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 8. This electronic part offers high-quality output due to its 2 channels. If the voltage supply is 2.3V volts, the electrical component should be turned on and run. As part of the design of the 8 series, this electronic part has been incorporated into the system. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Try searching with 74LVC2G66 to find analog multiplexer variants. A 10Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 8 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. The digital multiplexer has a low cost Single supply. 1.65V is the lowest voltage the electrical component should receive. For this multiplexer to operate, 10μA current would be sufficient. A voltage of 1.65V~5.5V is required for this switch device, which drains from a single voltage source. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. This analog switch ic utilizes SEPARATE OUTPUT output.