SN74LVC574ADBR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 156.687814mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74LVC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 1.65V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74LVC574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 150MHz |
| Propagation Delay | 7.8 ns |
| Turn On Delay Time | 7 ns |
| Family | LVC/LCX/Z |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 10μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 6.8ns @ 3.3V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
SN74LVC574ADBR Overview
20-SSOP (0.209, 5.30mm Width)is the packaging method. There is an embedded version in the package Tape & Reel (TR). As configured, the output uses Tri-State, Non-Inverted. JK flip flop uses Positive Edgeas the trigger. Surface Mountis in the way of this electric part. Powered by a 1.65V~3.6Vvolt supply, it operates as follows. It is operating at a temperature of -40°C~125°C TA. This logic flip flop is classified as type D-Type. FPGAs belonging to the 74LVCseries contain this type of chip. Its output frequency should not exceed 150MHz Hz. D latch consists of 1 elements. As a result, it consumes 10μA quiescent current and is not affected by external forces. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. This D latch belongs to the family of 74LVC574. A voltage of 1.8V provides power to the D latch. The input capacitance of this JK flip flopis 4pF farads. An electronic device belonging to the family LVC/LCX/Zcan be found here. It is mounted in the way of Surface Mount. A total of 20pins are provided on this board. A Positive Edgeclock edge trigger is used in this device. This part is included in FF/Latches. There are 8bits in its design. Using 8 circuits, it is highly flexible. This D flip flop is well suited for TR based on its reliable performance. This D flip flop is equipped with 0 ports. The output current of 24mA makes it feature maximum design flexibility. As of now, there are 3input lines.
SN74LVC574ADBR Features
Tape & Reel (TR) package
74LVC series
20 pins
8 Bits
SN74LVC574ADBR Applications
There are a lot of Texas Instruments SN74LVC574ADBR Flip Flops applications.
- Individual Asynchronous Resets
- Synchronous counter
- Buffered Clock
- Safety Clamp
- Shift Registers
- Power down protection
- Count Modes
- Guaranteed simultaneous switching noise level
- Bounce elimination switch
- Consumer
