SN74LVC574APWE4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Subcategory | Bus Driver/Transceiver |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Frequency | 150MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Temperature Grade | AUTOMOTIVE |
| Number of Circuits | 8 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 24mA |
| Number of Bits | 8 |
| Propagation Delay | 7.8 ns |
| Turn On Delay Time | 7 ns |
| Family | LVC/LCX/Z |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.024 A |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74LVC574APWE4 Overview
The flip flop is packaged in a case of TSSOP. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. Power is supplied from a voltage of 1.8V volts. A device of this type belongs to the family of LVC/LCX/Z. It is mounted by the way of Surface Mount. Basically, it is designed with a set of 20 pins. In this device, the clock edge trigger type is Positive Edge. This device is part of the Bus Driver/Transceiverbase part number family. An electronic part with 8bits has been designed. Its flexibility is enhanced by 8 circuits. Considering its reliability, this T flip flop is well suited for TUBE. The D flip flop has no ports embedded. There are 1 output lines on it. It is reported that there are 3 input lines. -24mA is set as the high level output current. 24mAis set as the low level output current. It is recommended that the operating temperature be lower than 125°C. In order for the system to operate properly, the temperature should be higher than -40°C. Initially, it requires a voltage of 1.65V as the minimum supply voltage. It is capable of supporting a maximum supply voltage of 3.6V. 150MHzis the maximum frequency that can be achieved. BUS DRIVERis used as the logic IC in this D flip flop. There are 1 functions available on the JK flip flop. There are 20 pins on the D latch. Its output current of 24mA allows for maximum design flexibility.
SN74LVC574APWE4 Features
20 pins
8 Bits
1 Functions
20 pin count
SN74LVC574APWE4 Applications
There are a lot of Texas Instruments SN74LVC574APWE4 Flip Flops applications.
- Modulo – n – counter
- ESCC
- Bounce elimination switch
- Counters
- Bus hold
- Data transfer
- Functionally equivalent to the MC10/100EL29
- Data Synchronizers
- High Performance Logic for test systems
- Event Detectors
