SN74LVC574ARGYR
| Parameters | |
|---|---|
| Length | 4.5mm |
| Width | 3.5mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-VFQFN Exposed Pad |
| Number of Pins | 20 |
| Weight | 43.006227mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74LVC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 1.65V~3.6V |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Base Part Number | 74LVC574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 150MHz |
| Propagation Delay | 7.8 ns |
| Turn On Delay Time | 7 ns |
| Family | LVC/LCX/Z |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 1.5μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 6.8ns @ 3.3V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1mm |
SN74LVC574ARGYR Overview
As a result, it is packaged as 20-VFQFN Exposed Pad. You can find it in the Cut Tape (CT)package. T flip flop is configured with an output of Tri-State, Non-Inverted. There is a trigger configured with Positive Edge. Surface Mountmounts this electrical part. The JK flip flop operates with an input voltage of 1.65V~3.6V volts. The operating temperature is -40°C~85°C TA. Logic flip flops of this type are classified as D-Type. JK flip flop belongs to the 74LVCseries of FPGAs. This D flip flop should not have a frequency greater than 150MHz. A total of 1elements are contained within it. As a result, it consumes 1.5μA quiescent current and is not affected by external forces. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. The 74LVC574 family contains this object. The D flip flop is powered by a voltage of 1.8V . The input capacitance of this T flip flop is 4pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. The electronic device belongs to the LVC/LCX/Zfamily. It is mounted in the way of Surface Mount. This board is designed with 20pins on it. A Positive Edgeclock edge trigger is used in this device. This device has the base part number FF/Latches. An electronic part designed with 8bits is used in this application. The superior flexibility is achieved through the use of 8 circuits. A reliable performance of this D flip flop makes it well suited for use in TR. A total of 2ports are embedded in the D flip flop. It offers maximum design flexibility with its output current of 24mA. A total of 3input lines have been provided.
SN74LVC574ARGYR Features
Cut Tape (CT) package
74LVC series
20 pins
8 Bits
SN74LVC574ARGYR Applications
There are a lot of Texas Instruments SN74LVC574ARGYR Flip Flops applications.
- Guaranteed simultaneous switching noise level
- Storage Registers
- Buffer registers
- Matched Rise and Fall
- Asynchronous counter
- Set-reset capability
- Counters
- Reduced system switching noise
- Functionally equivalent to the MC10/100EL29
- Bus hold
