SN74LVC74ADT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 12 hours ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74LVC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 1.65V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74LVC74 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 3.6V |
| Power Supplies | 3.3V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Clock Frequency | 150MHz |
| Propagation Delay | 6 ns |
| Turn On Delay Time | 1 ns |
| Family | LVC/LCX/Z |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 10μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 5.2ns @ 3.3V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LVC74ADT Overview
14-SOIC (0.154, 3.90mm Width)is the packaging method. D flip flop is embedded in the Tape & Reel (TR) package. T flip flop uses Differentialas the output. There is a trigger configured with Positive Edge. Surface Mountis in the way of this electric part. Powered by a 1.65V~3.6Vvolt supply, it operates as follows. A temperature of -40°C~125°C TAis considered to be the operating temperature. Logic flip flops of this type are classified as D-Type. FPGAs belonging to the 74LVCseries contain this type of chip. Its output frequency should not exceed 150MHz Hz. There is 10μA quiescent consumption. It has been determined that there have been 14 terminations. D latch belongs to the 74LVC74 family. The D flip flop is powered by a voltage of 1.8V . The input capacitance of this JK flip flopis 5pF farads. A device of this type belongs to the family of LVC/LCX/Z. There is an electronic part that is mounted in the way of Surface Mount. A total of 14pins are provided on this board. In this device, the clock edge trigger type is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. It reaches 3.6Vwhen the supply voltage is maximal (Vsup). Its flexibility is enhanced by 2 circuits. Due to its reliability, this T flip flop is well suited for TR. A total of 3.3V power supplies are needed to run it. The output current of 24mA makes it feature maximum design flexibility. The JK flip flop is with 1 output lines to operate.
SN74LVC74ADT Features
Tape & Reel (TR) package
74LVC series
14 pins
3.3V power supplies
SN74LVC74ADT Applications
There are a lot of Texas Instruments SN74LVC74ADT Flip Flops applications.
- Registers
- Latch-up performance
- 2 – Bit synchronous counter
- Digital electronics systems
- Individual Asynchronous Resets
- Frequency division
- Frequency Dividers
- Clock pulse
- Balanced Propagation Delays
- Set-reset capability
