SN74LVC823APWRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 24 |
| Weight | 89.499445mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 24 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | WITH CLEAR AND CLOCK ENABLE |
| Subcategory | Bus Driver/Transceiver |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Frequency | 150MHz |
| Pin Count | 24 |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 24mA |
| Propagation Delay | 8.9 ns |
| Turn On Delay Time | 1.3 ns |
| Family | LVC/LCX/Z |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 9 |
| Prop. Delay@Nom-Sup | 8 ns |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.15mm |
| Length | 7.8mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74LVC823APWRG4 Overview
TSSOPis the packaging method. A total of 1elements are present in it. There are 24 terminations,A voltage of 1.8V provides power to the D latch. In terms of electronic devices, this device belongs to the LVC/LCX/Zfamily of devices. The electronic part is mounted in the way of Surface Mount. With its 24pins, it is designed to work with most electronic flip flops. There is a clock edge trigger type of Positive Edgeon this device. There is a base part number Bus Driver/Transceiverfor the RS flip flops. A reliable performance of this D flip flop makes it well suited for use in TAPE AND REEL. There are 2 ports embedded in the flip flops. There are 3 output lines on it. There is also a characteristic of WITH CLEAR AND CLOCK ENABLE. High level output current is set to -24mA. A 24mAvalue is set for low-level output current. There should be a temperature below 85°Cduring operation. If the operating temperature is higher than -40°C, the system should operate properly. In order for it to operate, a supply voltage of 1.65Vis required. 3.6Vis the maximum supply voltage it supports. This frequency can be achieved 150MHz. It uses BUS DRIVERas its logic IC. The T flip flop is equipped with 1functions . The JK flip flop has a pin count of 24. As a result of its output current of 24mA, it is very flexible in terms of design.
SN74LVC823APWRG4 Features
24 pins
1 Functions
24 pin count
SN74LVC823APWRG4 Applications
There are a lot of Texas Instruments SN74LVC823APWRG4 Flip Flops applications.
- Communications
- EMI reduction circuitry
- Memory
- Frequency Divider circuits
- Convert a momentary switch to a toggle switch
- Load Control
- Registers
- Power down protection
- Balanced Propagation Delays
- Computers
