SN74LVTH273DWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74LVTH |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | BICMOS |
| Voltage - Supply | 2.7V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Base Part Number | 74LVTH273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 3.3V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 3.6V |
| Supply Voltage-Min (Vsup) | 2.7V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 64mA |
| Number of Bits | 8 |
| Clock Frequency | 150MHz |
| Propagation Delay | 3.2 ns |
| Turn On Delay Time | 3.2 ns |
| Family | LVT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 190μA |
| Current - Output High, Low | 32mA 64mA |
| Max I(ol) | 0.064 A |
| Max Propagation Delay @ V, Max CL | 4.9ns @ 3.3V, 50pF |
| Prop. Delay@Nom-Sup | 4.9 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Power Supply Current-Max (ICC) | 5mA |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LVTH273DWR Overview
As a result, it is packaged as 20-SOIC (0.295, 7.50mm Width). There is an embedded version in the package Cut Tape (CT). T flip flop uses Non-Invertedas the output. The trigger configured with it uses Positive Edge. It is mounted in the way of Surface Mount. A voltage of 2.7V~3.6Vis used as the supply voltage. It is at -40°C~85°C TAdegrees Celsius that the system is operating. It belongs to the type D-Typeof flip flops. FPGAs belonging to the 74LVTHseries contain this type of chip. This D flip flop should not have a frequency greater than 150MHz. D latch consists of 1 elements. During its operation, it consumes 190μA quiescent energy. A total of 20terminations have been recorded. You can search similar parts based on 74LVTH273. The D flip flop is powered by a voltage of 3.3V . JK flip flop input capacitance is 4pF farads. It belongs to the family of electronic devices known as LVT. A part of the electronic system is mounted in the way of Surface Mount. This board is designed with 20pins on it. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The RS flip flops belongs to FF/Latches base part number. The flip flop is designed with 8bits. The maximal supply voltage (Vsup) reaches 3.6V. Normal operation requires a supply voltage (Vsup) above 2.7V. Its superior flexibility is attributed to its use of 8 circuits. On the basis of its reliable performance, this D flip flop is well suited for use with TR. Optimal efficiency requires a supply voltage of 3.3V. In addition to its maximum design flexibility, the output current of the T flip flop is 64mA.
SN74LVTH273DWR Features
Cut Tape (CT) package
74LVTH series
20 pins
8 Bits
SN74LVTH273DWR Applications
There are a lot of Texas Instruments SN74LVTH273DWR Flip Flops applications.
- Pattern generators
- Power down protection
- CMOS Process
- Frequency Divider circuits
- ATE
- Automotive
- Data Synchronizers
- Divide a clock signal by 2 or 4
- ESD performance
- Test & Measurement
