SN74LVTH374DWE4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Frequency | 150MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Output Type | TTL |
| Operating Supply Voltage | 3.3V |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 8 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 2.7V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 64mA |
| Number of Bits | 8 |
| Propagation Delay | 2.9 ns |
| Turn On Delay Time | 2.9 ns |
| Family | LVT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.064 A |
| Prop. Delay@Nom-Sup | 4.5 ns |
| High Level Output Current | -32mA |
| Low Level Output Current | 64mA |
| Control Type | INDEPENDENT CONTROL |
| Power Supply Current-Max (ICC) | 5mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74LVTH374DWE4 Overview
It is packaged in the way of SOIC. T flip flop uses TTLas the output. There have been 20 terminations. The D flip flop is powered by a voltage of 3.3V . LVTis the family of this D flip flop. A part of the electronic system is mounted in the way of Surface Mount. With its 20pins, it is designed to work with most electronic flip flops. This device's clock edge trigger type is Positive Edge. This part is included in FF/Latches. It is designed with 8bits. In order to achieve its superior flexibility, 8 circuits are used. As a result of its reliable performance, this T flip flop is suitable for TUBE. The D flip flop has no ports embedded. For high efficiency, the supply voltage should be kept at 3.3V. There are 3 output lines in this JK flip flop. Currently, there are 1 lines of input. High level output current is set to -32mA. A 64mAvalue is set for low-level output current. There should be a temperature below 85°Cduring operation. It should be higher than -40°Cwhen the system is operating. A minimum supply voltage of 2.7V is required for these RS flip flops to operate. There is a maximum supply voltage of 3.6V. It is possible to achieve 150MHz frequencies. This logic IC is BUS DRIVER. Currently, it is equipped with 1 functions . It is equipped with 20 pins. Its output current of 64mA allows for maximum design flexibility.
SN74LVTH374DWE4 Features
20 pins
8 Bits
1 Functions
20 pin count
SN74LVTH374DWE4 Applications
There are a lot of Texas Instruments SN74LVTH374DWE4 Flip Flops applications.
- Computers
- Shift Registers
- Data storage
- Reduced system switching noise
- CMOS Process
- Balanced Propagation Delays
- Bounce elimination switch
- Storage Registers
- Single Up Count-Control Line
- Individual Asynchronous Resets
