SN74S112ADR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74S |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | JK Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | TTL |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74S112 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Output Current | 20mA |
| Clock Frequency | 125MHz |
| Propagation Delay | 7 ns |
| Turn On Delay Time | 4 ns |
| Family | S |
| Logic Function | AND, Flip-Flop |
| Current - Quiescent (Iq) | 25mA |
| Current - Output High, Low | 1mA 20mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 7ns @ 5V, 15pF |
| Trigger Type | Negative Edge |
| Number of Input Lines | 5 |
| Clock Edge Trigger Type | Negative Edge |
| Max Frequency@Nom-Sup | 80000000Hz |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
SN74S112ADR Overview
16-SOIC (0.154, 3.90mm Width)is the packaging method. The package Tape & Reel (TR)contains it. T flip flop uses Differentialas the output. Negative Edgeis the trigger it is configured with. There is an electronic component mounted in the way of Surface Mount. A supply voltage of 4.75V~5.25V is required for operation. It is operating at 0°C~70°C TA. This electronic flip flop is of type JK Type. This type of FPGA is a part of the 74S series. A frequency of 125MHzshould not be exceeded by its output. In total, it contains 2 elements. It consumes 25mA of quiescent The number of terminations is 16. If you search by 74S112, you will find similar parts. It is powered from a supply voltage of 5V. An electronic device belonging to the family Scan be found here. It is mounted in the way of Surface Mount. With its 16pins, it is designed to work with most electronic flip flops. This device has Negative Edgeas its clock edge trigger type. The part is included in FF/Latches. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. In order for the device to operate, it requires 5V power supplies. The 20mA output current allows it to be designed with the greatest amount of flexibility. The number of input lines is 5.
SN74S112ADR Features
Tape & Reel (TR) package
74S series
16 pins
5V power supplies
SN74S112ADR Applications
There are a lot of Texas Instruments SN74S112ADR Flip Flops applications.
- Count Modes
- Common Clocks
- Balanced 24 mA output drivers
- Consumer
- High Performance Logic for test systems
- Shift registers
- Safety Clamp
- Divide a clock signal by 2 or 4
- Test & Measurement
- Communications
