SN74S374DWE4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74S |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | TTL |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74S374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.25V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.75V |
| Number of Ports | 2 |
| Output Current | 20mA |
| Clock Frequency | 100MHz |
| Propagation Delay | 17 ns |
| Turn On Delay Time | 8 ns |
| Family | S |
| Logic Function | D-Type, Latch |
| Current - Quiescent (Iq) | 110mA |
| Max I(ol) | 0.02 A |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 17ns @ 5V, 15pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -6.5mA |
| Low Level Output Current | 20mA |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
SN74S374DWE4 Overview
The package is in the form of 20-SOIC (0.295, 7.50mm Width). D flip flop is embedded in the Tube package. As configured, the output uses Tri-State, Non-Inverted. JK flip flop uses Positive Edgeas the trigger. The electronic part is mounted in the way of Surface Mount. The supply voltage is set to 4.75V~5.25V. It is operating at a temperature of 0°C~70°C TA. The type of this D latch is D-Type. FPGAs belonging to the 74Sseries contain this type of chip. This D flip flop should not have a frequency greater than 100MHz. A total of 1 elements are present. As a result, it consumes 110mA of quiescent current without being affected by external factors. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. You can search similar parts based on 74S374. It is powered from a supply voltage of 5V. An electronic device belonging to the family Scan be found here. In this case, the electronic component is mounted in the way of Surface Mount. With its 20pins, it is designed to work with most electronic flip flops. This device exhibits a clock edge trigger type of Positive Edge. The part is included in FF/Latches. It reaches 5.25Vwhen the supply voltage is maximal (Vsup). Normally, the supply voltage (Vsup) should be kept above 4.75V. An electrical current of 5V volts is applied to it. The flip flop has 2embedded ports. It offers maximum design flexibility with its output current of 20mA. It has 3lines. It is set to -6.5mAfor the high level output current. In the low level output current setting, 20mAis used.
SN74S374DWE4 Features
Tube package
74S series
20 pins
5V power supplies
SN74S374DWE4 Applications
There are a lot of Texas Instruments SN74S374DWE4 Flip Flops applications.
- Clock pulse
- Memory
- Parallel data storage
- Individual Asynchronous Resets
- Consumer
- Single Up Count-Control Line
- Balanced 24 mA output drivers
- Dynamic threshold performance
- Power down protection
- ESD performance
