SN74S374NSRE4
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74S |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | TTL |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74S374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.25V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.75V |
| Number of Ports | 2 |
| Clock Frequency | 100MHz |
| Propagation Delay | 17 ns |
| Turn On Delay Time | 8 ns |
| Family | S |
| Logic Function | D-Type, Latch |
| Current - Quiescent (Iq) | 110mA |
| Max I(ol) | 0.02 A |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 17ns @ 5V, 15pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -6.5mA |
| Low Level Output Current | 20mA |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height Seated (Max) | 2mm |
| RoHS Status | ROHS3 Compliant |
| Mount | Surface Mount |
SN74S374NSRE4 Overview
The flip flop is packaged in a case of 20-SOIC (0.209, 5.30mm Width). The Tape & Reel (TR)package contains it. T flip flop uses Tri-State, Non-Invertedas its output configuration. It is configured with a trigger that uses a value of Positive Edge. In this case, the electronic component is mounted in the way of Surface Mount. A voltage of 4.75V~5.25Vis used as the supply voltage. It is at 0°C~70°C TAdegrees Celsius that the system is operating. A flip flop of this type is classified as a D-Type. It belongs to the 74Sseries of FPGAs. A frequency of 100MHzshould not be exceeded by its output. A total of 1 elements are present. There is a consumption of 110mAof quiescent energy. It has been determined that there have been 20 terminations. JK flip flop belongs to 74S374 family. Power is provided by a 5V supply. An electronic device belonging to the family Scan be found here. It is mounted by the way of Surface Mount. The 20pins are designed into the board. This device has the clock edge trigger type of Positive Edge. The part is included in FF/Latches. 5.25Vis the maximum supply voltage (Vsup). A normal operating voltage (Vsup) should remain above 4.75V. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. It runs on 5Vvolts of power. There are 2 ports embedded in the flip flops. This input has 3lines in it. -6.5mAis set as the high level output current. Low level output current is set to 20mA.
SN74S374NSRE4 Features
Tape & Reel (TR) package
74S series
20 pins
5V power supplies
SN74S374NSRE4 Applications
There are a lot of Texas Instruments SN74S374NSRE4 Flip Flops applications.
- ESCC
- Divide a clock signal by 2 or 4
- Test & Measurement
- Clock pulse
- Circuit Design
- Dynamic threshold performance
- CMOS Process
- Data transfer
- Data storage
- Convert a momentary switch to a toggle switch
