SP6686ER-L
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | DFN |
| Number of Pins | 10 |
| Packaging | Cut Tape |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Display Drivers |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.6V |
| Terminal Pitch | 0.5mm |
| Current Rating | 400mA |
| Frequency | 2.4MHz |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 10 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 3/5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Current | 500μA |
| Current - Output | 400mA |
| Quiescent Current | 500μA |
| Max Output Voltage | 6V |
| Voltage - Output | 6V |
| Topology | Charge Pump |
| Min Input Voltage | 2.7V |
| Frequency - Switching | 2.4MHz |
| Max Input Voltage | 5.5V |
| Output Current per Channel | 400mA |
| Min Output Voltage | -300mV |
| Interface IC Type | LED DISPLAY DRIVER |
| High Level Output Current | 400mA |
| Number of Segments | 1 |
| Multiplexed Display Capability | NO |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | Unknown |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SP6686ER-L Overview
The board's DFN package saves space. LED drivers design with 1 outputs.The frequency of 2.4MHz is used as the basis for its operation.In this case, it uses 10 terminations.This LED driver is configured with a base of 10 pins.A total of 1 segments have been created.The mount is on its way to Surface Mount.A voltage of 6V is produced by it.There are 10 pins on this device.According to its characteristics, it is also categorized into Display Drivers.A minimal input voltage of 2.7V is required for it to operate.Supply current cannot exceed 5.5V.It is possible to provide high efficiency when the maximal supply current is less than 500μA.It is important not to exceed 85°C in order to ensure stable operation.Maintaining a temperature above -40°C is essential for stabilizing operation.In order to power systems, 5.5V voltage is needed.The consumption of current is 500μAin the absence of external factors.In this part, LED DISPLAY DRIVER refers to the interface IC.If the output voltage exceeds 6V, it should be corrected.Maintain the part's output current at 400mA.It maintains a minimum voltage of -300mV.
SP6686ER-L Features
Available in the DFN package
Frequency of 2.4MHz
Supply voltage of 3.6V
Operating with the supply voltage of 5.5V
SP6686ER-L Applications
There are a lot of Exar Corporation SP6686ER-L LED Driver ICs applications.
- Replacement lamps
- Scanners and Handy Terminals
- Refrigeration lighting
- Flicker-free LED Lighting using R1580N
- Down lighting
- Stage Lighting and Signage
- Power source for accessories such as car audios, car navigation systems, and ETC systems
- OLED power supply for portable equipment
- General LED Lighting: Down-lights, Base-lights, Ceiling Lights, Exterior Lights
- LED backlight driver for LCD displays for Tablets and Note PCs
