ST485EXDR
| Parameters | |
|---|---|
| Transmit Delay-Max | 45 ns |
| Output Low Current-Max | 0.004A |
| Number of Transmitters | 1 |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Line Driver or Receivers |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ST485 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Nominal Supply Current | 900μA |
| Data Rate | 5Mbps |
| Differential Output | YES |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 70mV |
ST485EXDR Overview
Driver ICs with enhanced 8-SOIC (0.154, 3.90mm Width) packages are excellent for driving LEDs with common characteristics.The package of this receiver is Cut Tape (CT).With its Transceiver can transceiver design, this part can be incorporated into a wide range of solutions.PCB or development board with Surface Mount-type connectors can accommodate this wide receiver.It takes 4.75V~5.25V from the power supply to run this differential driver.At any given time, there can be up to 1/1 eligible receivers/drivers for this electronic part.Applications with operating temperatures of -55°C~125°C have been designed primarily for this ic receiver.Driver ICs in this category can operate efficiently with a supply voltage range of 5V.There are 8 pinouts available on this transceiver which are market standard.You can search with ST485 to get more variants of this part, since it identifies the product type, temperature, package, etc.An enhanced power dissipation control driver IC featuring 8 pins.The package size of this optical transceiver has been dramatically reduced by downsizing ICs and using high-density Surface Mount mounting techniques.It is important to note that this ic receiver had a maximum resolution of 1 bits.There is usually a 1-bit resolution specified for this receiver when it is used.There are two types of input voltage supply available for this IC, 5V.In this category, this rf transceiver module belongs to the Line Driver or Receivers subcategory.It is designed to be operated from a 5V power supply, so the module isolated transceiver will work effectively.An antenna transmits or sends data through 1 transmitters, which are can transceivers used to transmit radio waves to send data.
ST485EXDR Features
Cut Tape (CT) package
8 pin count
8 pins
5V power supply
ST485EXDR Applications
There are a lot of STMicroelectronics ST485EXDR Drivers/Receivers/Transceivers applications.
- Indoor ad hoc meeting
- Radio transmission
- Wireless communication
- Wireless 3D game
- IP cameras
- Aircraft navigation
- Notebook
- Vehicle
- Tuner
- SONET/SDH Network
