ST490ABDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Line Driver or Receivers |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ST490 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Interface | RS-422, RS-485 |
| Nominal Supply Current | 2mA |
| Data Rate | 25Mbps |
| Differential Output | YES |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Full |
| Receiver Hysteresis | 70mV |
| Receive Delay-Max | 30 ns |
| Simplex/Duplex | Full Duplex |
| Number of Transmitters | 1 |
| Height | 1.75mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
ST490ABDR Overview
An excellent driver IC for common LEDs thanks to its enhanced 8-SOIC (0.154, 3.90mm Width) package.There is a Cut Tape (CT) package for this receiver.As a Transceiver can transceiver, this part has enabled many applications to be served.On any Surface Mount-type PCB or development board, you can install this wide receiver.Power supply requirements for this differential driver are 4.5V~5.5V.Up to 1/1 receivers/drivers can be installed simultaneously on this electronic part.IC receiver is designed for applications with a temperature of -40°C~85°C.An operating voltage range of 5V is suitable for this line driver ic.There are 8 pinouts available on this transceiver which are market standard.With the part number ST490 identifying the product type, temperature, package, etc., you can search with it to see more variants.The driver IC has improved power dissipation control.Through optical transceiver downsizing and high-density Surface Mount mounting technologies, its package size is reduced dramatically.It is important to note that this ic receiver had a maximum resolution of 1 bits.There is usually a 1-bit resolution specified for this receiver when it is used.There is a 5V input voltage supply that can be used to operate this transceiver module.It is possible to subcategoriLine Driver or Receiverse this rf transceiver module as Line Driver or Receivers.An 8-pin power supply is provided by this driver IC, which allows it to operate from an 5V-pin power supply.1 transmitters are used in telecommunications to transmit or send data using radio waves.
ST490ABDR Features
Cut Tape (CT) package
8 pin count
8 pins
5V power supply
ST490ABDR Applications
There are a lot of STMicroelectronics ST490ABDR Drivers/Receivers/Transceivers applications.
- Shortwave receiver
- interconnection between computers
- Remote controls
- AV receiver
- Fiber optic cable connection network
- Servers
- Carrier phase observations
- Automation systems
- Cell phones
- Low power, low voltage systems
