ST890BDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 90mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Peripheral Drivers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Current Rating | 1.2A |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ST890 |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Output Type | P-Channel |
| Max Output Current | 1.2A |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 3/5V |
| Interface | On/Off |
| Nominal Supply Current | 13mA |
| Output Configuration | High Side |
| Output Current | 1.2A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 13mA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 50 μs |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 5.5V |
| Nominal Input Voltage | 5.5V |
| Turn-Off Delay Time | 10 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~5.5V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Adjustable), Over Temperature |
| Output Peak Current Limit-Nom | 1.2A |
| Rds On (Typ) | 75m Ω |
| Built-in Protections | OVER CURRENT; THERMAL |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
ST890BDR Overview
Tape & Reel (TR) is how it's packaged.It's included in the 8-SOIC (0.154, 3.90mm Width) package.A Surface Mount mounting is used for the LED driving board.A General Purpose switch type is owned by it.It is recommended that the temperature be set to -40°C~85°C TA for reliable operation.By default, it is set to output 1.It uses a supply voltage of Not Required to operate.The maximum output voltage is P-Channel volts.The ST890 family contains this object.As a result, there are 8 terminations.The operation is performed through the 8 pins.It contains 1 functions.As a result, the maximum output current is reduced to 1.2A in order to meet the operation requirements.The supply voltage can be 3V for high efficiency.It is positioned in the direction of Surface Mount.The LED driving board is equipped with a total of 8 pins.The LED driver has 90mOhm resistance.In this case, the output current will be set to 1.2A.This LED driver is self-contained in an econtainer with a capacity of Peripheral Drivers.3/5V is the power supply of the part.When using this LED driving board, it is recommended that the supply voltage is set to 5.5V.The maximum input voltage of the LED driver is 5.5V volts.It has a 2.7V volt minimum input voltage.It operates at a maximum current of 13mA.
ST890BDR Features
Supplied from 3V
Resistance of 90mOhm
ST890BDR Applications
There are a lot of STMicroelectronics ST890BDR Power Switches ICs applications.
- Wireless/Networking Cards
- Wearable Devices
- Notebook and Tablet Computers
- Wireless Headsets
- Hot Swaps
- Portable/Handheld Devices
- Hot-Swap Systems
- PC Card Hot Swap
- USB Power Distribution
- Gaming
