banner_page

ST890DTR

3/5V P-Channel 0.65mm PMIC ST890 8 Pin 3V 8-VDFN Exposed Pad


  • Manufacturer: STMicroelectronics
  • Nocochips NO: 761-ST890DTR
  • Package: 8-VDFN Exposed Pad
  • Datasheet: PDF
  • Stock: 255
  • Description: 3/5V P-Channel 0.65mm PMIC ST890 8 Pin 3V 8-VDFN Exposed Pad (Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 8-VDFN Exposed Pad
Number of Pins 8
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
JESD-609 Code e3
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
ECCN Code EAR99
Resistance 90mOhm
Terminal Finish Matte Tin (Sn) - annealed
Subcategory Peripheral Drivers
Terminal Position QUAD
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 3V
Terminal Pitch 0.65mm
Current Rating 1.2A
Base Part Number ST890
Pin Count 8
Number of Outputs 1
Output Type P-Channel
Max Output Current 1.2A
Operating Supply Voltage 5.5V
Power Supplies 3/5V
Interface On/Off
Output Configuration High Side
Output Current 1.2A
Voltage - Supply (Vcc/Vdd) Not Required
Input Type Non-Inverting
Turn On Delay Time 50 μs
Switch Type General Purpose
Min Input Voltage 2.7V
Max Input Voltage 5.5V
Nominal Input Voltage 5.5V
Turn-Off Delay Time 10 μs
Ratio - Input:Output 1:1
Voltage - Load 2.7V~5.5V
Driver Number of Bits 1
Fault Protection Current Limiting (Adjustable), Over Temperature
Output Peak Current Limit-Nom 1.2A
Rds On (Typ) 75m Ω
Built-in Protections OVER CURRENT; THERMAL
Height Seated (Max) 0.9mm
Length 3mm
Width 3mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Lead Free Lead Free

ST890DTR Overview


It is packaged in the form of a Tape & Reel (TR).The 8-VDFN Exposed Pad package contains it.Mounting type Surface Mount is selected for the LED driving board.This switch is of type General Purpose.To ensure reliable performance, the temperature should be set to -40°C~85°C TA.The LED driver has 1 outputs.The LED driving board operates with a supply voltage of Not Required.It has a maximum output voltage of P-Channel volts.It comes under the family of ST890.In total, there are 8 terminations.The 8 pins are used for the operation of the system.It is important to note that the LED driving board has 1 functions.The maximum output current is reduced to 1.2A to meet the operation criteria.It is possible to obtain high efficiency with a supply voltage of 3V.The lighting driver is mounted in the way of Surface Mount.There are 8 pins in total on this board.90mOhm is the resistance of the lighting driver.As a result, the output current is set to 1.2A.The LED driver is packaged in an econtainer with a capacity of Peripheral Drivers.This part has a power supply of 3/5V volts.It is recommended that the supply voltage be set at 5.5V in order to achieve maximum efficiency.The maximum input voltage of the LED driver is 5.5V volts.The input voltage minimum is 2.7V volts.

ST890DTR Features


Supplied from 3V
Resistance of 90mOhm

ST890DTR Applications


There are a lot of STMicroelectronics ST890DTR Power Switches ICs applications.

  • USB Ports/Hubs
  • Storage (HDDs, SSDs)
  • PC Card Hot Swap
  • USB Power Distribution
  • Storage Drives
  • Hard Disk Drives
  • Wireless Modem Data Cards
  • Notebook PC
  • PDAs
  • PC Cards

Write a review

Note: HTML is not translated!
    Bad           Good