STG3699BVTR
| Parameters | |
|---|---|
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-UFQFN |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 500mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.12W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | STG3699 |
| Pin Count | 16 |
| Number of Outputs | 8 |
| Operating Supply Voltage | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 50nA |
| Nominal Supply Current | 50nA |
| Power Dissipation | 1.12W |
| Max Supply Current | 50nA |
| Turn On Delay Time | 55 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 30 ns |
| -3db Bandwidth | 40MHz |
| On-State Resistance (Max) | 500mOhm |
| High Level Output Current | 300mA |
| Low Level Output Current | 300mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 64 dB |
| Current - Leakage (IS(off)) (Max) | 20nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 0.15Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 55ns, 30ns |
| Charge Injection | 57pC |
| Channel-to-Channel Matching (ΔRon) | 150m Ω |
| Crosstalk | -72dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Height Seated (Max) | 0.6mm |
| Length | 2.6mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
STG3699BVTR Overview
This electronic part is conveniently packaged in 16-UFQFN, making it easy to ship abroad. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 2:1. Operating temperature extended to -55°C~125°C TA. Total terminations are 16. Due to its 1 channels, the electrical component produces high-quality output. An 1.8V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 16 pins. SPDT switching circuits are used in these analog switch ics. Try searching for the analog switch ic with STG3699 if you are looking for variants. Analog switches have 500mOhm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 4.3V voltage to the switch device. Analog switch ics with Single supply type are cost-effective. 1.65V is the lowest voltage that should be fed to the electronic electronic part. This digital switch can be operated with a current of 50nA. A voltage of 1.65V~4.3V is required for this switch device, which drains from a single voltage source. A digital multiplexer may suffer damage if voltage is applied above 50nA. This electrical part is compatible with 3V operating voltages. It is possible to operate 4 inputs. The analogue multiplexer has 8 outputs.
STG3699BVTR Features
1 Channels
Switch Circuit: SPDT
50nA Supply Current
-3db Bandwidth: 40MHz
STG3699BVTR Applications
There are a lot of STMicroelectronics STG3699BVTR Analog Switches & Multiplexers ICs applications.
- Sample-and-hold systems
- Channelized and Unchannelized DS3 applications
- Data switching
- High reliability control systems
- DSUs
- Cross Connects
- Cable PC
- T1/E1 Terminals
- Medical Instrumentation
- Audio signal routing
