STG3856QTR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 12-UFQFN |
| Number of Pins | 12 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 12 |
| ECCN Code | EAR99 |
| Resistance | 1Ohm |
| Terminal Finish | Nickel/Palladium (Ni/Pd) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 18.5mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.4mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | STG3856 |
| Pin Count | 12 |
| Number of Outputs | 6 |
| Number of Channels | 3 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.4V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 50nA |
| Nominal Supply Current | 50nA |
| Max Supply Current | 50nA |
| Turn On Delay Time | 50 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 25 ns |
| -3db Bandwidth | 100MHz |
| On-State Resistance (Max) | 1Ohm |
| Multiplexer/Demultiplexer Circuit | 3:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 20nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 0.01Ohm |
| Switch Circuit | SP3T |
| Switch Time (Ton, Toff) (Max) | 40ns, 20ns |
| Charge Injection | 55pC |
| Channel-to-Channel Matching (ΔRon) | 10m Ω |
| Crosstalk | -84dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Drain to Source Resistance | 1Ohm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
STG3856QTR Overview
Shipping overseas is convenient due to the electrical component's packing in 12-UFQFN. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 3:1. Operational temperature extended around -55°C~125°C TA. In total, there are 12 terminations. The electronic part delivers high-quality output through its 3 channels. With a 2.7V voltage supply, the electrical component should be turned on and run. A total of 12 pins are injected into the body of the electronic part. These analog multiplexers are built based on SP3T switching circuits. Try searching with STG3856 to find analog multiplexer variants. An switch multiplexer with 1Ohm internal resistance has a value of 1Ohm. Datasheets for functions of 12 pins are available. The analog multiplexer shown here is a typical Multiplexer or Switches. Users should never supply a voltage higher than 4.3V to a switch device. Single supply type digital switch with a low cost. It is recommended to use 1.4V as the lowest voltage for the electrical part. The switch device would be able to operate with 50nA current. A voltage of 1.65V~4.3V is required for this switch device, which drains from a single voltage source. Putting voltage greater than 50nA on the multiplexer may cause damage. With a DIFFERENTIAL MULTIPLEXER analog IC integrated into the board. Among the inputs that can be operated are the 2 inputs. There is 1Ohm Drain to Source resistance on this electronic part. Multiplexer ics with 6 outputs are available.
STG3856QTR Features
3 Channels
Switch Circuit: SP3T
50nA Supply Current
-3db Bandwidth: 100MHz
Drain-to-Source resistance: 1Ohm
STG3856QTR Applications
There are a lot of STMicroelectronics STG3856QTR Analog Switches & Multiplexers ICs applications.
- Modems
- RGB switches
- PCMCIA cards
- Imaging
- Microwave transmission systems
- DSUs
- Public switching systems
- Medical systems
- SDH
- Mechanical reed relay replacement
