STG5223QTR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFQFN |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 500mOhm |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.12W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3.3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | STG5223 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Number of Channels | 1 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 50nA |
| Nominal Supply Current | 50nA |
| Power Dissipation | 1.12W |
| Max Supply Current | 50nA |
| Turn On Delay Time | 120 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 45 ns |
| -3db Bandwidth | 55MHz |
| On-State Resistance (Max) | 500mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 66 dB |
| Current - Leakage (IS(off)) (Max) | 20nA |
| Channel Capacitance (CS(off), CD(off)) | 40pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 55ns, 30ns |
| Charge Injection | 49pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -72dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 65ns |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Height Seated (Max) | 0.55mm |
| Length | 1.8mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
STG5223QTR Overview
The electrical component comes in 10-UFQFN packaging, which makes it convenient to ship overseas. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. A total of 10 terminations have been recorded. The electronic part provides high-quality output because it has 1 channels. Turning on and running the electrical part should be easy with a 3.3V voltage supply. It is injected into the electrical part body with 10 pins. Based on SPDT switching circuits, these analog multiplexers work. Use STG5223 to search for variants of the digital switches. This digital multiplexer has 500mOhm internal resistance. For functions related to 10 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. A voltage higher than 4.3V should not normally be supplied to the switches. Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 1.65V. This multiplexer would work with 50nA current. A voltage of 1.65V~4.3V is required for this switch device, which drains from a single voltage source. If put voltage greater than 50nA on the device, damage may be caused to the analogue multiplexer. In order to operate the 2 inputs, there are several steps to follow. A analog switch ics with 4 outputs is included.
STG5223QTR Features
1 Channels
Switch Circuit: SPDT
50nA Supply Current
-3db Bandwidth: 55MHz
STG5223QTR Applications
There are a lot of STMicroelectronics STG5223QTR Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- SDH
- Microwave transmission systems
- Audio and video signal routing
- MP3 players
- Avionics and Military Systems
- Power routing
- Microprocessor Controlled Analog Systems
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Automatic test equipment
