banner_page

STG5682QTR

80ns, 50ns SPDT 550mOhm QUAD Analog Switches BREAK-BEFORE-MAKE STG5682 16 Pins 100nA 1.8V 16-UFQFN


  • Manufacturer: STMicroelectronics
  • Nocochips NO: 761-STG5682QTR
  • Package: 16-UFQFN
  • Datasheet: PDF
  • Stock: 173
  • Description: 80ns, 50ns SPDT 550mOhm QUAD Analog Switches BREAK-BEFORE-MAKE STG5682 16 Pins 100nA 1.8V 16-UFQFN(Kg)

Details

Tags

Parameters
Lifecycle Status ACTIVE (Last Updated: 6 months ago)
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 16-UFQFN
Number of Pins 16
Weight 57.09594mg
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
ECCN Code EAR99
Resistance 550mOhm
Subcategory Multiplexer or Switches
Max Power Dissipation 1.12W
Technology CMOS
Terminal Position QUAD
Number of Functions 2
Supply Voltage 1.8V
Terminal Pitch 0.4mm
Base Part Number STG5682
Output SEPARATE OUTPUT
Pin Count 16
Power Supplies 1.8/5V
Number of Channels 1
Number of Circuits 2
Max Supply Voltage 4.5V
Min Supply Voltage 1.65V
Operating Supply Current 50nA
Nominal Supply Current 50nA
Max Supply Current 50nA
Turn On Delay Time 80 ns
Supply Type Single
Turn-Off Delay Time 50 ns
-3db Bandwidth 33MHz
On-State Resistance (Max) 550mOhm
Multiplexer/Demultiplexer Circuit 2:1
Off-state Isolation-Nom 55 dB
Current - Leakage (IS(off)) (Max) 100nA
Channel Capacitance (CS(off), CD(off)) 6pF
On-state Resistance Match-Nom 0.05Ohm
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 80ns, 50ns
Charge Injection 126pC
Channel-to-Channel Matching (ΔRon) 15m Ω
Crosstalk -60dB @ 100kHz
Switching BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+) 1.65V~4.5V
Height Seated (Max) 0.6mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Lead Free Lead Free

STG5682QTR Overview


The electronic component is convenient to ship overseas because it is packed in a 16-UFQFN. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. 16 terminations have been made so far. Due to its 1 channels, the electrical component produces high-quality output. If the voltage supply is 1.8V volts, the electrical component should be turned on and run. A total of 16 pins are injected into the body of the electronic part. Based on SPDT switching circuits, these analog multiplexers work. The multiplexer consists of 2 circuits. Use STG5682 to search for variants of the digital switches. There is 550mOhm internal resistance in this digital multiplexer. For details about the functions of 16 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 4.5V to the switch device in normal circumstances. Single supply type digital switch with a low cost. The lowest voltage the electronic part should receive is 1.65V. For this multiplexer to operate, 50nA current would be sufficient. Using a single voltage supply, this switch device consumes 1.65V~4.5V volts. It may damage the digital multiplexer if the voltage is higher than 50nA. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.

STG5682QTR Features


1 Channels
Switch Circuit: SPDT
50nA Supply Current
-3db Bandwidth: 33MHz

STG5682QTR Applications


There are a lot of STMicroelectronics STG5682QTR Analog Switches & Multiplexers ICs applications.

  • Industrial
  • Power routing
  • Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
  • Microwave transmission systems
  • FTTH
  • Precision test equipment
  • Low-Voltage
  • Precision data acquisition
  • Channel Banks
  • E1 Network Equipment

Write a review

Note: HTML is not translated!
    Bad           Good