STG719CTR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 4Ohm |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.95mm |
| Base Part Number | STG719 |
| Pin Count | 6 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 10 ns |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 5.5 ns |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 74 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 19pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 7ns, 4.5ns (Typ) |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -52dB @ 1MHz |
| Switch-off Time-Max | 8.5ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
STG719CTR Overview
Presented in SOT-23-6, this electrical component is convenient for overseas shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. 2:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of -55°C~125°C TA degrees Celsius. 6 terminations have been made so far. High-quality output is provided by the electronic component's 1 channels. When the electronic component is given a voltage of 3.3V, it should be turned on and run. This electrical component is included in the 6 series of products. These analog multiplexers are built based on SPDT switching circuits. 1 circuits are used in this analogue multiplexer. Try searching with STG719 if you're looking for variants. The internal resistance of this digital multiplexer is 4Ohm. The datasheets for the 6 pins explain the functions. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. A cost-effective Single supply type analogue multiplexer. A low voltage of 1.8V should be applied to the electronic component. For this digital switch to work, 1μA current would suffice. This analog switch requires a voltage of 1.8V~5.5V to drain from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 1μA. This switch operates within the bandwidth of 200MHz.
STG719CTR Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
Bandwidth: 200MHz
STG719CTR Applications
There are a lot of STMicroelectronics STG719CTR Analog Switches & Multiplexers ICs applications.
- USB 1.1 signal switching circuits
- E1 Network Equipment
- DVD-R
- Automatic test equipment
- Microprocessor controlled systems
- New designs requiring multiplexer functions
- Industrial and process control systems
- Cell phones
- Audio and video signal routing
- FTTH
