STG719STR
| Parameters | |
|---|---|
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Weight | 36.003894mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | STG719 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 7 ns |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 4.5 ns |
| On-State Resistance (Max) | 4Ohm |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 74 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 19pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 7ns, 4.5ns (Typ) |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -52dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 6.35mm |
| Length | 6.35mm |
| Width | 6.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
STG719STR Overview
Presented in SOT-23-6, this electrical component is convenient for overseas shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. Around -55°C~125°C TA is the extended operating temperature. 6 terminations have been made so far. The electronic part delivers high-quality output through its 1 channels. When a voltage supply of 3.3V is used, the electronic component should be turned on and run. An electrical component of this type can be found in the 6 series. Unlike digital switches, these are based on SPDT switching circuits. Try searching for STG719 variants of the analog switch ic. It has an internal resistance of 4Ohm. Datasheets for functions of 6 pins are available. There is a standard Multiplexer or Switches analogue multiplexer here. Users shouldn't supply more than 5.5V voltage to the switch device. A cost-effective Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 1.8V. The analogue multiplexer could operate on 1μA current. Analogue multiplexers require a 1.8V~5.5V voltage to drain from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. 200MHz-bandwidths can be used to transfer data between multiplexers. An output of 2 is provided by the digital multiplexer.
STG719STR Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
Bandwidth: 200MHz
STG719STR Applications
There are a lot of STMicroelectronics STG719STR Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- DSLAMs
- Fault Tolerant Systems
- RGB switches
- Communication systems
- Microprocessor Controlled Analog Systems
- Industrial control systems
- Automotive applications
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- DVD-R
