STM690RM6F
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 320mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.6V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | STM690 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 60μA |
| Nominal Supply Current | 60μA |
| Power Dissipation | 320mW |
| Max Supply Current | 60μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 2.625V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 2.55V |
| Max Reset Threshold Voltage | 2.7V |
| Undervoltage Threshold | 2.55V |
| Overvoltage Threshold | 2.7V |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
STM690RM6F Overview
A total of 8 terminals are used to mount this power management. In terms of packaging, power management follows the Tape & Reel (TR) model. As a reference, this IC management includes 1 functions for your convenience. Depending on the power managment ic you are looking at, you can find a total of 1 channels. In this IC management you will find 8-SOIC (0.154, 3.90mm Width) functions for you to refer to. This IC power shares lots of benefits with other Simple Reset/Power-On Reset products. Specifies a reflow peak temperature of 260 for the package during reflow. IC management conducts at a voltage of 3.6V. In a 1 supply voltage, the PMIC chip conducts. Power management is included in the Surface Mount mount. Power Management Circuits is a subcategory of this PMIC chip. In total, IC powers are 8 pins on the board. This power management system has 8 pins. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1V. During this IC power, the maximum supply voltage (Vsup) should not exceed 5.5V volts. A Surface Mount mounting type is recommended. We recommend setting the supervisors to -40°C~85°C TA degrees. While this power management is operating, it will output Push-Pull, Totem Pole as the output voltage. The power management's supply current is 60μA. You can always use STM690, the base supervisor number, to search for similar PMICs of the manufacturer. The voltage supervisor requires a power source of 3/5V volts in order to work correctly. The maximum supply temperature that PMIC chip can work with is 60μA.
STM690RM6F Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
60μA operating supply current
STM690RM6F Applications
There are a lot of STMicroelectronics STM690RM6F Voltage Supervisors applications.
- Military communications
- Urban rail transit weak current power monitoring
- Set top box
- Consumer electronics
- Insulation fault location system
- Personal computers
- Detection of phase loss
- External alarm
- Power communication system
- Automotive permanent magnet synchronous motors
