STM706TAM6F
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 320mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Base Part Number | STM706 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 40μA |
| Nominal Supply Current | 60μA |
| Power Dissipation | 320mW |
| Max Supply Current | 60μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 3.08V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 160ms Minimum |
| Min Reset Threshold Voltage | 3V |
| Max Reset Threshold Voltage | 3.15V |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
STM706TAM6F Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 8 in total. Packaging is in the form of a Tape & Reel (TR). As a reference, this IC management includes 1 functions for your convenience. There are a total of 1 channels on this supervisor, and they are arranged in a series. In this IC management you will find 8-SOIC (0.154, 3.90mm Width) functions for you to refer to. This IC power shares lots of benefits with other Simple Reset/Power-On Reset products. According to the specification, the package's peak reflow temperature is specified to be 260. The supervisor is always powered by a 3.3V volt supply. When 1 is applied to the power ic, it conducts. Power management is included in the Surface Mount mount. It is possible to subcategorize this power ic as a Power Management Circuits chip. A total of 8 pins are located on this power management. 8 pins make up the power management. Supply voltage (Vsup) should be at least 1V for this power management. It is recommended that the maximum supply voltage (Vsup) in this IC power be no more than 5.5V volts. The mounting type of the supervisors is Surface MountIt is recommended that the supervisor be set to this temperature: -40°C~85°C TA. The output voltage of this power managment ic during operation is Push-Pull, Totem Pole. For this power management, there is an 40μA volt supply current. A similar IC managements number of the manufacturer can always be found by using STM706, the base power ics number. The power management can work with a maximum supply temperature of 60μA.
STM706TAM6F Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
40μA operating supply current
STM706TAM6F Applications
There are a lot of STMicroelectronics STM706TAM6F Voltage Supervisors applications.
- Battery cars
- Radar
- Medical-specific insulation monitor
- Multi-voltage system
- Automotive power systems
- Automotive permanent magnet synchronous motors
- External alarm
- Detection of phase imbalance
- Insulation fault location system
- Dash board
