STM795TM6F
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 320mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.6V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | STM795 |
| Output | Open Drain or Open Collector |
| Pin Count | 8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 60μA |
| Nominal Supply Current | 60μA |
| Power Dissipation | 320mW |
| Max Supply Current | 60μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 3.075V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 3V |
| Max Reset Threshold Voltage | 3.15V |
| Undervoltage Threshold | 3V |
| Overvoltage Threshold | 3.15V |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
STM795TM6F Overview
Power management is mounted through 8 terminals. Power management is packaged in a Tape & Reel (TR) way. There are 1 functions included in this PMIC so that you can refer to them. It is possible to find on this power management a series of 1 channels. To assist you, this PMIC includes 8-SOIC (0.154, 3.90mm Width) functions. There are a lot of similarities between this IC power and other Simple Reset/Power-On Reset products. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 260. IC management conducts at a voltage of 3.6V. IC management is possible to find a succession of 1 voltages that have been checked. Surface Mount is the one that mounts power management. There is a subcategory called Power Management Circuits for this power management. It has a total of 8 pins that are attached to IC management. This power management has 8 pins. IC management can only work with a supply voltage of 1V volts. In this PMIC, the maximum supply voltage (Vsup) should not exceed 5.5V volts. The recommended mounting type for IC management is Surface Mount. It is recommended to set the supervisor's temperature to this range: -40°C~85°C TA. As a result of this supervisor's operation, the output voltage is Open Drain or Open Collector. The supervisor's supply current is specified to 60μA. For similar manage ics search of the manufacturer, you can always refer to STM795, the base PMIC number. It requires 3.3/5V watts of power to operate this voltage supervisor. If you want to work with PMIC chip, you will need to supply PMIC chip with a temperature at least of 60μA.
STM795TM6F Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
60μA operating supply current
STM795TM6F Applications
There are a lot of STMicroelectronics STM795TM6F Voltage Supervisors applications.
- Battery cars
- Electronics installed in the vehicle
- Important electronics for automotive protection
- Consumer electronics
- Detection of phase sequence
- DSP
- DC stabilized power supply module
- Medical-specific isolation transformer
- Smart meter
- Power communication system
