STM810RWX6F
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-236-3, SC-59, SOT-23-3 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 320mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | STM810 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 3 |
| Max Output Current | 20mA |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 15μA |
| Nominal Supply Current | 7μA |
| Power Dissipation | 320mW |
| Max Supply Current | 15μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active High |
| Voltage - Threshold | 2.63V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 2.59V |
| Max Reset Threshold Voltage | 2.66V |
| Threshold Voltage | +2.63V |
| Undervoltage Threshold | 2.59V |
| Overvoltage Threshold | 2.66V |
| Length | 2.92mm |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
STM810RWX6F Overview
A total of 3 terminals are used to mount this power management. There is a Cut Tape (CT)-packaging method applied to IC management. In this IC power you will find 1 functions for you to refer to. A series of 1 channels can be found on this supervisor. To assist you, this PMIC includes TO-236-3, SC-59, SOT-23-3 functions. As with other Simple Reset/Power-On Reset products, this IC management also offers a wide range of benefits. Specifies a reflow peak temperature of 260 for the package during reflow. A supply voltage of 3.3V is used to conduct the PMIC chip. IC management is possible to find a succession of 1 voltages that have been checked. By Surface Mount, IC management has been mounted. Power Management Circuits is a subcategory of this PMIC chip. In total, the power management has 3 pins in it. The pins of the power management system count 3. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 1V volts. This IC power should be powered by no more than 5.5V volts of supply voltage (Vsup). Power management' mounting is recommended to be done with the Surface Mount type of mounting. You should set the supervisor's temperature during -40°C~85°C TA . While in operation, this supervisor has a voltage output of Push-Pull, Totem Pole. The supervisor's supply current is specified to 15μA. You can always use STM810, the base supervisor number, to search for similar PMICs of the manufacturer. At most, voltage supervisor can operate at a supply temperature of 15μA.
STM810RWX6F Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
15μA operating supply current
STM810RWX6F Applications
There are a lot of STMicroelectronics STM810RWX6F Voltage Supervisors applications.
- Power distribution systems of CCU
- Power distribution systems of operating room
- Cloud computing
- Transformer load monitoring equipment
- Battery cars
- Display equipment
- Detection of phase sequence
- Solar power charger
- Detection of phase loss
- Unattended substation automation
