STMPS2141TTR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 130mOhm |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 32.5mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Current Rating | 500mA |
| Base Part Number | STMPS2141 |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Operating Supply Voltage | 5.5V |
| Interface | On/Off |
| Nominal Supply Current | 40μA |
| Output Configuration | High Side |
| Power Dissipation | 32.5mW |
| Output Current | 0A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 40μA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 5 ms |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 5.5V |
| Turn-Off Delay Time | 10 ms |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~5.5V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Reverse Current, UVLO |
| Turn On Time | 5000 µs |
| Rds On (Typ) | 110m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; THERMAL; UNDER VOLTAGE |
| Length | 4.4mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
STMPS2141TTR Overview
As a result, it is packaged in the form of a Tape & Reel (TR).Package 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) contains it.A Surface Mount mounting is used for the LED driving board.It owns the General Purpose switch type.Keeping the temperature at -40°C~125°C TJ ensures reliable operation.The LED driver is equipped with 1 outputs.It uses a supply voltage of Not Required to operate.A maximum output voltage of N-Channel volts can be achieved by this LED driver.The STMPS2141 family contains this object.It contains 8 terminations.8 pins are used for operation.It is important to note that the LED driving board has 1 functions.Supply voltages of 5V allow for high efficiency.The LED driving board is mounted in the way of Surface Mount.8 pins are equipped with it.130mOhm resistance is present in the lighting driver.When this is the case, the output current is set to 0A.A self-contained econtainer holding Peripheral Drivers capacity contains this lighting driver.Optimal efficiency requires a voltage of 5.5V.This LED driver can handle voltages up to 5.5V volts.As far as input voltage goes, it has a minimum of 2.7V volts.It has a maximum current requirement of 40μA.
STMPS2141TTR Features
Supplied from 5V
Resistance of 130mOhm
STMPS2141TTR Applications
There are a lot of STMicroelectronics STMPS2141TTR Power Switches ICs applications.
- Notebook PC
- Portable GPS
- Storage (HDDs, SSDs)
- HDD and SSD
- Hot Swap
- Low Voltage I/O System Power
- Set-top-box
- USB Protection
- USB Ports/Hubs
- Telecom and Network Systems
