STMPS2252MTR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 160mOhm |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Current Rating | 500mA |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | STMPS2252 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 2 |
| Interface | On/Off |
| Analog IC - Other Type | POWER SUPPLY SUPPORT CIRCUIT |
| Output Configuration | High Side |
| Output Current | 0A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Adjustable Threshold | NO |
| Input Type | Non-Inverting |
| Turn On Delay Time | 5 ms |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 5.5V |
| Nominal Input Voltage | 5V |
| Turn-Off Delay Time | 10 ms |
| Ratio - Input:Output | 1:2 |
| Voltage - Load | 2.7V~5.5V |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Reverse Current, UVLO |
| Rds On (Typ) | 105m Ω |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
STMPS2252MTR Overview
Cut Tape (CT) is the way it's packaged.The 8-SOIC (0.154, 3.90mm Width) package contains it.The lighting driver has the mounting type Surface Mount.This switch is of type General Purpose.To ensure reliable performance, the temperature should be set to -40°C~125°C TJ.The lighting driver is equipped with 2 outputs that can be used.In order to operate, it requires a voltage supply of Not Required.This object belongs to the STMPS2252 family.It consists of 8 terminations in total.In order to operate, the 8 pins are used.There are 1 functions of the LED driver.It is possible to achieve a high level of efficiency with a supply voltage of 5V.Surface Mount is mounted in the way of this lighting driver.A total of 8 pins are present on it.In this LED driving board, there is 160mOhm resistance.In this case, the output current will be set to 0A.In this lighting driver, POWER SUPPLY SUPPORT CIRCUIT is the analog IC.In total, there are 2 channels available.The supply voltage should be set at 5.5V for best efficiency.As far as input voltage goes, its maximum is 5.5V volts.A voltage of 2.7V volts is the minimum input voltage.
STMPS2252MTR Features
Supplied from 5V
Resistance of 160mOhm
2 channels
STMPS2252MTR Applications
There are a lot of STMicroelectronics STMPS2252MTR Power Switches ICs applications.
- USB Power Distribution
- Wireless Headsets
- Wearable Devices
- Low Voltage I/O System Power
- Set-top-box
- Hot Swap
- Set-Top Boxes
- PDAs
- Portable GPS Device
- Solid-State Drives
