SY100EL29VZG
| Parameters | |
|---|---|
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | -3V~-5.5V |
| Frequency | 1.1GHz |
| Base Part Number | 100EL29 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Max Supply Voltage | -5.5V |
| Min Supply Voltage | -3V |
| Output Current | 50mA |
| Number of Bits | 2 |
| Clock Frequency | 1.1GHz |
| Propagation Delay | 720 ps |
| Quiescent Current | 50mA |
| Turn On Delay Time | 720 ps |
| Logic Function | AND |
| Current - Quiescent (Iq) | 50mA |
| Number of Bits per Element | 1 |
| Trigger Type | Positive Edge |
| High Level Output Current | -50mA |
| Low Level Output Current | 50mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SOIC |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| Series | 100EL |
| Part Status | Active |
SY100EL29VZG Overview
It is packaged in the way of 20-SOIC (0.295, 7.50mm Width). A package named Tubeincludes it. The output it is configured with uses Differential. It is configured with the trigger Positive Edge. This electronic part is mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of -3V~-5.5V volts. In this case, the operating temperature is -40°C~85°C TA. It belongs to the type D-Typeof flip flops. It is a type of FPGA belonging to the 100EL series. Its output frequency should not exceed 1.1GHz Hz. There are 2 elements in it. It consumes 50mA of quiescent If you search by 100EL29, you will find similar parts. It is mounted in the way of Surface Mount. This board is designed with 20pins on it. This device's clock edge trigger type is Positive Edge. The flip flop is designed with 2bits. To achieve this superior flexibility, 2 circuits are used. Featuring the maximum design flexibility, it has an output current of 50mA . There are 1 output lines on it. Currently, there are 1 input lines present. Quiescent current is consumed by the D latch in the amount of 50mA. The high level output current is set to -50mA. The low level output current is set to 50mA. It is recommended that the operating temperature be below 85°C. In order for the system to operate properly, the temperature should be higher than -40°C. The minimum voltage required for operation is -3V. The maximum supply voltage supported by the flip flop is -5.5V. This frequency can be achieved 1.1GHz.
SY100EL29VZG Features
Tube package
100EL series
20 pins
2 Bits
SY100EL29VZG Applications
There are a lot of Microchip Technology SY100EL29VZG Flip Flops applications.
- Frequency Dividers
- 2 – Bit synchronous counter
- Digital electronics systems
- Data transfer
- Memory
- Shift Registers
- Individual Asynchronous Resets
- Power down protection
- Communications
- Pattern generators
