SY10EP51VZG-TR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Supplier Device Package | 8-SOIC |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Series | 10EP |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | -3V~-5.5V |
| Frequency | 3GHz |
| Base Part Number | 10EP51 |
| Function | Reset |
| Output Type | Differential |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | -3V |
| Number of Bits | 1 |
| Clock Frequency | 3GHz |
| Propagation Delay | 370 ps |
| Quiescent Current | 40mA |
| Turn On Delay Time | 500 ps |
| Current - Quiescent (Iq) | 40mA |
| Number of Bits per Element | 1 |
| Trigger Type | Positive, Negative |
| High Level Output Current | -50mA |
| Low Level Output Current | 50mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | ROHS3 Compliant |
SY10EP51VZG-TR Overview
The flip flop is packaged in a case of 8-SOIC (0.154, 3.90mm Width). The package Tape & Reel (TR)contains it. Differentialis the output configured for it. This trigger uses the value Positive, Negative. There is an electrical part that is mounted in the way of Surface Mount. The JK flip flop operates at -3V~-5.5Vvolts. It is operating at a temperature of -40°C~85°C TA. A flip flop of this type is classified as a D-Type. It is a type of FPGA belonging to the 10EP series. In order for it to function properly, its output frequency should not exceed 3GHz. The element count is 1 . T flip flop consumes 40mA quiescent energy. You can search similar parts based on 10EP51. There is an electronic component mounted in the way of Surface Mount. As you can see from the design, it has pins with 8. This device's clock edge trigger type is Positive Edge. 1bits are used in its design. The superior flexibility of this circuit is achieved by using 1 circuits. To operate, the chip has a total of 1 output lines. There are 1 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. Quiescent current is consumed by the D latch in the amount of 40mA. In this case, the high level output current is set to -50mA. A 50mAvalue is set for low-level output current. Ideally, the operating temperature should be lower than 85°C. If the operating temperature is higher than -40°C, the system should operate properly. Initially, it requires a voltage of -3V as the minimum supply voltage. There is a maximum voltage support of 5.5V. This frequency can be achieved at 3GHz.
SY10EP51VZG-TR Features
Tape & Reel (TR) package
10EP series
8 pins
1 Bits
SY10EP51VZG-TR Applications
There are a lot of Microchip Technology SY10EP51VZG-TR Flip Flops applications.
- Computers
- Dynamic threshold performance
- Storage Registers
- Modulo – n – counter
- Parallel data storage
- Memory
- Safety Clamp
- Cold spare funcion
- Latch-up performance
- Set-reset capability
