TC110333ECTTR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | PFM CONTROL TECHNIQUE IS ALSO POSSIBLE |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | TC110 |
| Function | Step-Up |
| Number of Outputs | 1 |
| Output Voltage | 3.3V |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 10V |
| Input Voltage-Nom | 3.3V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 300mA |
| Voltage - Supply (Vcc/Vdd) | 2V~10V |
| Control Features | Enable, Soft Start |
| Input Voltage (Min) | 2V |
| Topology | Boost |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 100kHz~300kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Switcher Configuration | SINGLE |
| Max Frequency | 345kHz |
| Duty Cycle (Max) | 92% |
| Length | 2.9mm |
| RoHS Status | ROHS3 Compliant |
TC110333ECTTR Overview
Capsuled in the SC-74A, SOT-753 package, the switching controller can be used for a wide range of applications. There is sufficient capacity to generate switching controller for outputs 1. PMIC packaging is solid with a Tape & Reel (TR) enclosure. With Transistor Driver dc switching's output (s), it is able to handle it. dc controls with 2V~10V voltage are supplied and operated. Suitable for working in an dc switcher that has a -40°C~85°C TA. It can switch at 100kHz~300kHz. dc dc regulator is made easier with Surface Mount. In order to control switching efficiently, the dcdc regulator features Enable, Soft Start. The switch converters are connected to a SWITCHING CONTROLLER analog IC. There are a terminal (s) on the switching converters that are designed at DUAL. 5 terminations with a variety of function. Some of the control techniques adapted by these dc dc converter ics include PULSE WIDTH MODULATION. The nominal DC switcher's voltage input is 3.3V. Other relevant dc to dc converter ics can be found by searching "TC110". In total, switching converter has 5 pins. Specially, switching converter corresponds to type Switching Regulator or Controllers. It is recommended that the dc dc voltage regulator's minimum input voltage be 2V. DC regulator outputs 3.3V voltage based on test statistics. A starting point for a project is to note down the dc dc regulator's usual output current, which is 300mA. In most applications and prototype designs, DC switcher is qualified as a Surface Mount. 345kHz is the maximum frequency of this dc regulators. The value of DC to DC voltage regulator is set to PFM CONTROL TECHNIQUE IS ALSO POSSIBLE in order to better satisfy the requirement. To operate the voltage regulator dc to dc safely and reliably, users should apply 10V.
TC110333ECTTR Features
Transistor Driver Outputs
Switching Frequency: 100kHz~300kHz
Enable, Soft Start
PULSE WIDTH MODULATION
PFM CONTROL TECHNIQUE IS ALSO POSSIBLE
TC110333ECTTR Applications
There are a lot of Microchip Technology TC110333ECTTR DC to DC converter applications.
- CMM
- Servo drive system
- ATMs
- Sensitive electronic devices
- Computed tomography (CT)
- Scientific research
- Digital video recorders
- Die casting equipment
- Milling machines
- Boring machines
