TC1276-10ENBTR
| Parameters | |
|---|---|
| Undervoltage Threshold | 2.8V |
| Overvoltage Threshold | 2.97V |
| Length | 2.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-236-3, SC-59, SOT-23-3 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 230mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | TC1276 |
| Output | Open Drain or Open Collector |
| Pin Count | 3 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 350μA |
| Power Dissipation | 230mW |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 2.88V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 100ms Minimum |
| Supply Current-Max (Isup) | 0.7mA |
| Min Reset Threshold Voltage | 2.8V |
| Max Reset Threshold Voltage | 2.97V |
| Threshold Voltage | +2.88V |
TC1276-10ENBTR Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 3 in total. Power management is packaged in a Tape & Reel (TR) way. There are 1 functions included in this PMIC so that you can refer to them. Power management consists of 1 channels, each of which can be used independently. In this PMIC, you can find TO-236-3, SC-59, SOT-23-3 functions for your reference. Compared to other Simple Reset/Power-On Reset products, this PMIC has a lot of benefits to offer. Specifies a reflow peak temperature of 260 for the package during reflow. During operation, the power ic is supplied with a voltage of 3.3V. Power management conducts at a voltage of 1. Surface Mount is the one that mounts power management. The power management system can be categorized as a Power Management Circuits chip. There are a total of 3 pins on power management. 3 pins are on the supervisor. In order for this IC power to function, the supply voltage (Vsup) cannot be less than 1.2V. In this PMIC, the maximum supply voltage (Vsup) should not exceed 5.5V volts. Power management recommends the Surface Mount mounting type. This power management is the recommended temperature range for the supervisors: -40°C~85°C TA. Power management has an output of Open Drain or Open Collector during operation. It is estimated that the voltage supervisor's supply current is 350μA. A similar IC managements number of the manufacturer can always be found by using TC1276, the base power ics number.
TC1276-10ENBTR Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
350μA operating supply current
TC1276-10ENBTR Applications
There are a lot of Microchip Technology TC1276-10ENBTR Voltage Supervisors applications.
- Multi-voltage system
- Cloud computing
- Battery cars
- Fire equipment power monitoring system
- Military electronics
- Magnetic resonance imaging
- Automotive permanent magnet synchronous motors
- Power distribution systems of operating room
- Analog circuit
- Detection of phase loss
