TC54VC2702EMB713
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-243AA |
| Number of Pins | 3 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | SINGLE |
| Terminal Form | FLAT |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | TC54VC2702 |
| Output | Push-Pull, Totem Pole |
| Number of Channels | 1 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 700mV |
| Operating Supply Current | 3.6μA |
| Power Dissipation | 500mW |
| Adjustable Threshold | NO |
| Quiescent Current | 1.1μA |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 2.7V |
| Number of Voltages Monitored | 1 |
| Supply Current-Max (Isup) | 0.004mA |
| Min Reset Threshold Voltage | 2.65V |
| Max Reset Threshold Voltage | 2.75V |
| Threshold Voltage | +2.7V |
| Undervoltage Threshold | 2.65V |
| Overvoltage Threshold | 2.75V |
| Height | 1.6mm |
| Length | 4.6mm |
| Width | 2.6mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
TC54VC2702EMB713 Overview
It is mounted through 3 terminals on the power management. Packaged in the form of a Tape & Reel (TR), power management is easy to use. For your reference, this IC power includes a list of 1 functions. A series of 1 channels can be found on this supervisor. To assist you, this PMIC includes TO-243AA functions. There are a number of benefits that this PMIC has in common with other Simple Reset/Power-On Reset manage ics. Specifies a reflow peak temperature of 260 for the package during reflow. A supply voltage of 2V is used to conduct the PMIC chip. Power ics operate at 1 supply voltages. The mount is attached to Surface Mount. As a subcategory, this PMIC chip can be categorized as Power Management Circuits. 3 pins make up the power management. In order for this IC power to function, the supply voltage (Vsup) cannot be less than 700mV. The maximum supply voltage (Vsup) is not to exceed 10V volts in this IC management. The recommended mounting type is Surface Mount. This range of temperature should be set for the supervisors: -40°C~85°C TA. During operation, this power management system outputs Push-Pull, Totem Pole. For this power management, there is an 3.6μA volt supply current. It is always advisable to use TC54VC2702, the base supervisor number, when searching for similar PMICs from the manufacturer.
TC54VC2702EMB713 Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 700mV
3.6μA operating supply current
TC54VC2702EMB713 Applications
There are a lot of Microchip Technology TC54VC2702EMB713 Voltage Supervisors applications.
- Microprocessor system
- Important electronics for automotive protection
- Dash board
- DVR
- Power communication system
- DC stabilized power supply module
- WiFi router
- Utility meter
- Efficient information transmission
- Detection of phase loss
