TC54VC2902EMB713
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-243AA |
| Number of Pins | 3 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | SINGLE |
| Terminal Form | FLAT |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | TC54VC2902 |
| Output | Push-Pull, Totem Pole |
| Number of Channels | 1 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 700mV |
| Operating Supply Current | 3.6μA |
| Power Dissipation | 500mW |
| Adjustable Threshold | NO |
| Quiescent Current | 1.1μA |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 2.9V |
| Number of Voltages Monitored | 1 |
| Supply Current-Max (Isup) | 0.004mA |
| Min Reset Threshold Voltage | 2.84V |
| Max Reset Threshold Voltage | 2.96V |
| Threshold Voltage | +2.9V |
| Undervoltage Threshold | 2.84V |
| Overvoltage Threshold | 2.96V |
| Length | 4.495mm |
| Width | 2.445mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
TC54VC2902EMB713 Overview
There are 3 terminals connected to this power management, which makes it easy to mount. Packaged in the form of a Tape & Reel (TR), power management is easy to use. For your reference, this IC power includes a list of 1 functions. On this supervisor, there is a series of 1 channels that can be found. Please refer to power management for TO-243AA functions. It is a IC power that shares many benefits with other products from the Simple Reset/Power-On Reset line. The package peak reflow temperature is specified to be 260. The supervisor is always powered by a 2V volt supply. A supply voltage of 1 is used to conduct the PMIC chip. The power management is mounted by Surface Mount. It is possible to subcategorize this power ic as a Power Management Circuits chip. 3 pins are on the supervisor. In order for this PMIC to work correctly, the minimum supply voltage (Vsup) should be greater than 700mV. In this PMIC, the maximum supply voltage (Vsup) should not exceed 10V volts. In this case, Surface Mount is the recommended mounting type. The temperature of the supervisors should be set to this range: -40°C~85°C TA. There is an output voltage of Push-Pull, Totem Pole from this supervisor when it is operating. For this power management, there is an 3.6μA volt supply current. A similar IC managements number of the manufacturer can always be found by using TC54VC2902, the base power ics number.
TC54VC2902EMB713 Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 700mV
3.6μA operating supply current
TC54VC2902EMB713 Applications
There are a lot of Microchip Technology TC54VC2902EMB713 Voltage Supervisors applications.
- Detection of phase sequence
- Rechargeable batteries
- Automotive permanent magnet synchronous motors
- Leakage current detection
- emergency room
- Detection of phase loss
- Radio
- Multi-voltage system
- Unattended substation automation
- External alarm
