TC74ACT273P
| Parameters | |
|---|---|
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ACT273 |
| JESD-30 Code | R-PDIP-T20 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 150MHz |
| Propagation Delay | 10.5 ns |
| Quiescent Current | 8μA |
| Family | ACT |
| Current - Output High, Low | 75mA 75mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 10.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 4.45mm |
| Length | 24.6mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1996 |
| Series | TC74ACT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
TC74ACT273P Overview
The package is in the form of 20-DIP (0.300, 7.62mm). Package Tubeembeds it. T flip flop is configured with an output of Non-Inverted. The trigger it is configured with uses Positive Edge. Through Holemounts this electrical part. The supply voltage is set to 4.5V~5.5V. Temperature is set to -40°C~85°C TA. It belongs to the type D-Typeof flip flops. The TC74ACTseries comprises this type of FPGA. Its output frequency should not exceed 150MHz. A total of 1 elements are present. The number of terminations is 20. You can search similar parts based on 74ACT273. The D flip flop is powered by a voltage of 5V . Input capacitance of this device is 5pF farads. An electronic device belonging to the family ACTcan be found here. There is an electronic component mounted in the way of Through Hole. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This device has the base part number FF/Latches. An electronic part designed with 8bits is used in this application. In this case, the maximum supply voltage (Vsup) reaches 5.5V. For normal operation, the supply voltage (Vsup) should be kept above 4.5V. Using 8 circuits, it is highly flexible. The D latch runs on a voltage of 5V volts. There is 8μA quiescent current consumption by it.
TC74ACT273P Features
Tube package
TC74ACT series
8 Bits
5V power supplies
TC74ACT273P Applications
There are a lot of Toshiba Semiconductor and Storage TC74ACT273P Flip Flops applications.
- Clock pulse
- High Performance Logic for test systems
- ESD protection
- Modulo – n – counter
- Computers
- Guaranteed simultaneous switching noise level
- Storage Registers
- Bounce elimination switch
- Parallel data storage
- Frequency Dividers
