TC74HC175AP
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| Series | TC74HC |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 4.5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HC175 |
| Function | Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 4 |
| Load Capacitance | 50pF |
| Number of Bits | 4 |
| Clock Frequency | 63MHz |
| Propagation Delay | 175 ns |
| Turn On Delay Time | 16 ns |
| Family | HC/UH |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 24ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| fmax-Min | 29 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 25000000Hz |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
TC74HC175AP Overview
The flip flop is packaged in 16-DIP (0.300, 7.62mm). The package Tubecontains it. T flip flop uses Differentialas its output configuration. In the configuration of the trigger, Positive Edgeis used. There is an electronic component mounted in the way of Through Hole. With a supply voltage of 2V~6V volts, it operates. A temperature of -40°C~85°C TAis considered to be the operating temperature. D-Typeis the type of this D latch. It is a type of FPGA belonging to the TC74HC series. In order for it to function properly, its output frequency should not exceed 63MHz. D latch consists of 1 elements. As a result, it consumes 4μA of quiescent current without being affected by external factors. Terminations are 16. The 74HC175family includes it. A voltage of 4.5V is used as the power supply for this D latch. Its input capacitance is 5pF farads. This D flip flop belongs to the family of HC/UH. In this case, the electronic component is mounted in the way of Through Hole. This board is designed with 16pins on it. This device has the clock edge trigger type of Positive Edge. The part you are looking for is included in FF/Latches. 4bits are used in its design. As soon as 6Vis reached, Vsup reaches its maximum value. The supply voltage (Vsup) should be maintained above 2V for normal operation. The superior flexibility of this product is achieved by using 4 circuits. It operates from 2/6V power supplies.
TC74HC175AP Features
Tube package
TC74HC series
16 pins
4 Bits
2/6V power supplies
TC74HC175AP Applications
There are a lot of Toshiba Semiconductor and Storage TC74HC175AP Flip Flops applications.
- Consumer
- Shift Registers
- Guaranteed simultaneous switching noise level
- ESD protection
- Latch-up performance
- Circuit Design
- Data storage
- Computing
- Synchronous counter
- ESD performance
