TC74HC4051AF(EL,F)
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Published | 2006 |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 4.5V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Power Dissipation | 180mW |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 2V~6V ±2V~6V |
| Neg Supply Voltage-Nom (Vsup) | -4.5V |
| -3db Bandwidth | 85MHz |
| On-State Resistance (Max) | 100Ohm |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 70pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Time (Ton, Toff) (Max) | 18ns, 29ns |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Crosstalk | -50dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.025A |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
TC74HC4051AF(EL,F) Overview
Due to its 16-SOIC (0.209, 5.30mm Width) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Cut Tape (CT). Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a number of circuits 8:1. Operating temperature around -40°C~85°C TA extended. 16 terminations have been made so far. As a result of its 8 channels, this electronic component provides high-quality output. Powered by a 4.5V voltage supply, the electrical part should be switched on and run. 1 circuits are used in this analogue multiplexer. You can find the functions of the 16 pins in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 6V volts for the multiplexer. It is recommended to use 2V as the lowest voltage for the electrical part. It is integrated with SINGLE-ENDED MULTIPLEXER analog ICs. In order to operate the 8 inputs, there are several steps to follow.
TC74HC4051AF(EL,F) Features
8 Channels
-3db Bandwidth: 85MHz
TC74HC4051AF(EL,F) Applications
There are a lot of Toshiba Semiconductor and Storage TC74HC4051AF(EL,F) Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- Relay replacements
- Video switching
- Intelligent PBX
- SONET/SDH ADM
- Fiber to the Home
- Audio/video switches
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Channelized and Unchannelized DS3 applications
- SONET
